Manwal tal-Utent tal-Kwikset 910 SmartCode Deadbolt Elettroniku Tradizzjonali bit-Teknoloġija Z-Wave

1. Prodott Aktarview

The Kwikset 910 SmartCode Traditional Electronic Deadbolt with Z-Wave Technology offers keyless entry and enhanced security for your home. This deadbolt integrates with Z-Wave home automation systems, allowing for remote control and monitoring. It features a backlit keypad for increased visibility and SmartKey Security as a backup keyway.

Karatteristiċi ewlenin:

• Keyless entry with a customizable keypad.
• Z-Wave technology for integration with compatible smart home systems.
• Program up to 30 user access codes.
• One-touch locking motorized deadbolt.
• SmartKey Security for easy re-keying and advanced break-in protection.
• Operates on 4 AA batteries.

2. Setup u Installazzjoni

X'inhu Inkluż:

• Electronic deadbolt assembly
• Ħardwer tal-immuntar
• Ċwievet

Għodod Meħtieġa:

• Tornavit tar-ras Phillips
• Tejp kejl

Passi ta' Installazzjoni:

1. Ipprepara l-Bieb: Ensure your door is properly prepped for a deadbolt. Check backset, cross-bore, and edge-bore dimensions.
2. Installa Lukkett: Insert the latch into the door edge. Ensure the bolt is facing the correct direction. Secure with screws.
3. Installa l-Istrike Plate: Install the strike plate on the door frame, aligning it with the latch bolt. Secure with screws.
4. Installa l-Assemblea Esterni: Place the exterior keypad assembly on the door, ensuring the torque blade passes through the latch.
5. Installa l-Pjanċa tal-Immuntar Interna: Route the wiring harness through the mounting plate and secure the plate to the exterior assembly with screws.
6. Connect Wiring and Install Interior Assembly: Connect the wiring harness to the interior assembly. Align the torque blade with the turn piece shaft and secure the interior assembly to the mounting plate with screws.
7. Installa Batteriji: Insert 4 AA batteries into the battery pack.
8. Wettaq il-Proċess tal-Immaniġġjar tal-Bieb: While holding down the Lock button on the keypad, insert the battery pack. Continue holding until the deadbolt cycles and stops, indicating successful door handing.

3. Istruzzjonijiet Operattivi

Qfil tal-Bieb:

• Qfil One-Touch: Press the Lock button on the keypad. The deadbolt will extend to lock the door.
• Qfil Manwali: From the interior, turn the thumb turn to the locked position.

Niftaħ il-Bieb:

• Using a User Code: Enter a valid 4-8 digit user code on the keypad. The deadbolt will retract to unlock the door.
• L-użu taċ-Ċavetta: Insert the physical key into the keyway and turn it to unlock the door.
• Manual Unlocking: From the interior, turn the thumb turn to the unlocked position.

Kodiċi tal-Utent tal-Programmazzjoni:

1. Iftaħ il-bieb.
2. Agħfas il-buttuna tal-Programm darba.
3. Daħħal kodiċi tal-utent ġdid ta' 4-8 ċifri.
4. Press the Lock button to save the code.
5. Test the new user code with the door open to ensure it works correctly.

To add additional user codes, repeat the process, pressing the Program button the corresponding number of times (e.g., twice for the second code, three times for the third, etc.).

4. Manutenzjoni

Sostituzzjoni tal-batterija:

When the batteries are low, the lock will emit a series of beeps and the keypad will flash red. To replace the batteries:

1. Neħħi l-għatu ta 'ġewwa.
2. Neħħi l-pakkett tal-batterija.
3. Replace all four AA batteries with new alkaline batteries.
4. Reinsert the battery pack and replace the cover.

SmartKey Re-keying:

The SmartKey Security feature allows you to re-key your lock to a new key in seconds, providing convenience and enhanced security.

1. Insert your functioning key (the key currently operating the lock) and turn it 90 degrees clockwise.
2. Insert the SmartKey tool fully and firmly into the SmartKey hole.
3. Remove the SmartKey tool.
4. Remove your functioning key.
5. Insert your new key fully and firmly into the keyway.
6. Turn the new key 90 degrees counter-clockwise.
7. Remove the new key. The lock is now re-keyed to the new key.

5 Issolvi l-problemi

Kwistjonijiet Komuni u Soluzzjonijiet:

• Is-serratura ma tirrispondix: Check battery levels and replace if necessary. Ensure the battery pack is properly seated.
• User code not working: Verify the code is entered correctly. Re-program the user code if unsure.
• Deadbolt not extending/retracting smoothly: Check for obstructions in the door frame or latch. Ensure the lock is properly aligned and mounted.
• Z-Wave connectivity issues: Refer to your Z-Wave hub's instructions for pairing and troubleshooting. Ensure the lock is within range of the hub.
• It-tastiera ma tixgħelx: Check batteries. If the issue persists, contact customer support.

6. Speċifikazzjonijiet

7. Garanzija u Appoġġ

Kwikset products are designed for durability and reliability. For specific warranty information, please refer to the warranty card included with your product or visit the official Kwikset website. For technical assistance, troubleshooting, or to inquire about replacement parts, please contact Kwikset customer support.

Riżorsi onlajn: Għal aktar appoġġ u riżorsi, żur il- Ħanut Kwikset fuq Amazon.