Prodott Overview
The Telwin Telmig 170/1 Turbo is a versatile welding machine designed for both FLUX (no gas) and MIG-MAG (gas) welding processes. It offers flexibility for use with various materials including steel, stainless steel, and aluminum. The machine is equipped with thermostatic protection for enhanced safety and durability. It comes with essential MIG-MAG welding accessories and supports a 5 kg wire spool.
Immaġni: Quddiem view of the Telwin Telmig 170/1 Turbo welding machine, showing its red and black casing, control panel, wheels, and connected welding cables with torch and earth clamp.
Setup Istruzzjonijiet
- Spakkjar: Carefully remove the welding machine and all accessories from the packaging. Inspect for any shipping damage.
- Pjazzament: Place the machine on a stable, level surface in a well-ventilated area, away from flammable materials.
- Konnessjoni tal-Enerġija: Ensure the machine is switched off. Connect the power cable to a suitable 230V single-phase power outlet with a 16A fuse.
- Installazzjoni tar-Rukkell tal-Wajer: Open the wire compartment and install a 5 kg welding wire spool (e.g., steel, stainless steel, or aluminum wire with appropriate diameter). Ensure the wire feeds smoothly through the guide.
- Konnessjoni Aċċessorju:
- Connect the MIG Torch (2.5M, part no. 742393) to the designated port on the machine.
- Attach the Toledo 250 Earth Clamp (250A, part no. 712030) to the workpiece.
- For MIG-MAG welding, connect the Argon Cylinder Adapter (part no. 432036) and the Rechargeable Cylinder Pressure Reducer (part no. 722341) to a gas cylinder, then connect the gas hose to the machine.
- Kontrolli Inizjali: Before powering on, double-check all connections for security and proper fit.
Istruzzjonijiet Operattivi
The Telmig 170/1 Turbo supports both FLUX (gasless) and MIG-MAG (with gas) welding. Select the appropriate mode and settings based on your material and welding requirements.
- Għażla tal-Modalità: Choose between FLUX (no gas) or MIG-MAG (gas) welding depending on your wire type and application.
- Kompatibbiltà tal-Materjal: This machine is suitable for welding steel, stainless steel, and aluminum. Ensure you use the correct wire type and diameter for the material being welded.
- Regulation Positions: The machine features 6 regulation positions to adjust the welding current. Start with a lower setting and gradually increase until the desired arc stability and penetration are achieved.
- Wire Diameter Selection:
- Steel Welding Wire: 0.6 - 0.8 mm
- Stainless Steel Welding Wire: 0.8 mm
- Aluminum Welding Wire: 0.8 - 1 mm
- Proċess tal-Iwweldjar:
- Ilbes tagħmir protettiv personali (PPE) xieraq, inkluż elmu tal-iwweldjar, ingwanti, u ħwejjeġ protettivi.
- Ixgħel il-magna.
- Initiate the arc by pressing the torch trigger. Maintain a consistent travel speed and arc length for optimal results.
- The machine features thermostatic protection, which will automatically shut down the unit if it overheats. Allow it to cool down before resuming operation.
Manutenzjoni
Manutenzjoni regolari tiżgura l-lonġevità u l-prestazzjoni ottimali tal-magna tal-iwweldjar tiegħek.
- Tindif: Periodically clean the machine's exterior with a dry cloth. Ensure ventilation openings are free from dust and debris.
- Sistema ta' Għalf tal-Wajer: Spezzjona r-rombli u l-inforra tal-alimentazzjoni tal-wajer għal xedd jew imblukkar. Naddaf jew ibdel kif meħtieġ biex tiżgura alimentazzjoni bla xkiel tal-wajer.
- Torch and Earth Clamp: Check the torch nozzle, contact tip, and earth clamp for wear or damage. Replace consumables as needed. Ensure all connections are tight.
- Spezzjoni tal-Cable: Regularly inspect all cables (power, torch, earth) for cuts, abrasions, or loose connections. Repair or replace damaged cables immediately.
- Ħażna: When not in use, store the machine in a dry, clean environment, protected from dust and moisture.
Issolvi l-problemi
Din it-taqsima tipprovdi soluzzjonijiet għal kwistjonijiet komuni li tista’ tiltaqa’ magħhom.
- Machine Does Not Power On:
- Check if the power cable is securely plugged into both the machine and the power outlet.
- Verify that the power outlet is functional and the circuit breaker or fuse (16A) has not tripped.
- Ensure the machine's power switch is in the "ON" position.
- No Arc or Weak Arc:
- Iċċekkja l-earth clamp connection to the workpiece; ensure it is clean and secure.
- Inspect the welding wire for proper feeding and ensure the contact tip is not clogged or worn.
- Verify that the welding current settings are appropriate for the material thickness.
- For MIG-MAG welding, ensure gas flow is adequate and the gas cylinder is not empty.
- Machine Overheats (Thermostatic Protection Activated):
- The machine has built-in thermostatic protection. If it shuts down, allow it to cool down for a sufficient period (typically 10-15 minutes) before restarting.
- Ensure adequate ventilation around the machine and that cooling vents are not obstructed.
- Reduce the duty cycle or welding current if continuous operation is causing frequent overheating.
- Kwalità Fqira tal-Weldjatura:
- Adjust welding current and wire feed speed settings.
- Ensure the workpiece is clean and free of rust, paint, or grease.
- Check for proper gas shielding (for MIG-MAG) and correct torch angle.
Speċifikazzjonijiet Tekniċi
Detailed specifications for the Telwin Telmig 170/1 Turbo welding machine.
| Parametru | Valur |
|---|---|
| Single-Phase Mains Voltage | 230 V |
| Frekwenza tal-Mejns | 50 / 60 Hz |
| Medda tar-Regolament | 30 - 160 A |
| Max Current (15%) | 140 A |
| Current at 60% | 80 A |
| Max bla tagħbija Voltage | 31 V |
| Max Assorbita Enerġija | 5.2 kW |
| Absorbed Power at 60% | 2.3 kW |
| Fjus tal-Mejns | 16 A |
| Power Factor (cosphi) | 0.9 |
| Regulation Positions | 6 |
| Welding Wire Diameter (Steel) | 0.6 - 0.8 mm |
| Welding Wire Diameter (Stainless Steel) | 0.8 mm |
| Welding Wire Diameter (Aluminum) | 0.8 - 1 mm |
| Grad ta' Protezzjoni | IP21 |
| Dimensjonijiet (L x W x H) | 80 x 45 x 57 ċm |
| Piż | 37 kg |
| Kodiċi EAN | 8004897598352 |
| Numru tal-Mudell | TE-821054 |
Image: A table illustrating electrical specifications such as voltage, current range, maximum current, and fuse rating for the welding machine.
Image: A table illustrating additional specifications including power factor, number of regulation positions, compatible wire diameters for steel, stainless steel, and aluminum, IP protection rating, dimensions, and weight.
Aċċessorji Inklużi
The Telwin Telmig 170/1 Turbo comes equipped with the following accessories:
- Argon Cylinder Adapter (Part No. 432036)
- MIG Torch 2.5M (Part No. 742393)
- Cable 16 MMQ 1.8M (Part No. 120302)
- Rechargeable Cylinder Pressure Reducer (Part No. 722341)
- Toledo 250 Earth Clamp 250A (Part No. 712030)
Garanzija u Appoġġ
For detailed warranty information, please refer to the warranty card included with your product or contact your authorized Telwin dealer or the manufacturer directly. Support inquiries can be directed to Telwin's official customer service channels, typically found on their websit.
