1. Introduzzjoni
Grazzi tax-xiriasing the Matrix DX1800.5 1800 Watt 5-Channel MOSFET Car Power Amplifier. This manual provides comprehensive instructions for the proper installation, operation, and maintenance of your new amplifier. Please read this manual thoroughly before attempting to install or operate the amplifier to ensure optimal performance and safety.
2. Informazzjoni dwar is-Sigurtà
- Always disconnect the vehicle's battery negative terminal before starting any installation.
- Kun żgur li l-wajers kollha huma mgħoddija u mwaħħlin sew biex tevita li jinqerdu jew jagħmlu ħsara.
- Uża wajers tal-enerġija u tal-ert tal-kejl xieraq kif speċifikat fit-taqsima tal-installazzjoni.
- Tarmax il- ampLififier f'żoni esposti għax-xemx diretta, sħana eċċessiva, umdità, jew trab.
- Jekk m'intix ċert dwar xi parti tal-proċess tal-installazzjoni, ikkonsulta installatur professjonali tal-awdjo tal-karozzi.
- Dan amplifier is designed for 12V DC negative ground systems only.
3. Prodott Aktarview
The Matrix DX1800.5 is a high-performance 5-channel car power amplifier designed to deliver clear and powerful audio. It features a robust MOSFET power supply and versatile crossover controls for precise sound tuning.
Karatteristiċi ewlenin:
- 5-Channel 1800 Watt MOSFET Power Ampaktar ħaj
- Maximum Power Rating (4 Ohm): 125 Watts x 4 Channels + 480 Watts x 1 Channel
- Maximum Power Rating (2 Ohm): 250 Watts x 4 Channels + 800 Watts x 1 Channel
- PWM DC to DC Power Supply for stable performance
- Operazzjoni Stereo Stabbli ta '2 Ohm
- Built-in Variable High Pass Filter (40 Hz - 3 kHz)
- Built-in Variable Low Pass Filter (40 Hz - 250 Hz)
- Built-in Bass Boost Control (0/+6/+12 dB)
- RCA Speaker / Line Output
- Comprehensive Protection Circuits (Short Circuit, Thermal, Speaker)
- Indikaturi LED ta' Enerġija u Protezzjoni
- Channel Separation: Greater than 60 dB
- Includes Bass Boost Remote Control
Prodott Views:
4. Setup u Installazzjoni
Installazzjoni xierqa hija kruċjali għall-prestazzjoni u l-lonġevità tiegħek amplifier. Segwi dawn il-passi bir-reqqa.
4.1 Post tal-Immuntar
Choose a mounting location that is dry, well-ventilated, and away from direct heat sources. Ensure there is sufficient airflow around the amplifier. Common locations include the trunk, under seats, or behind rear seats.
4.2 Konnessjonijiet tal-Wiring
- Power (BATT+): Connect a direct wire from the positive terminal of the vehicle's battery to the BATT+ terminal on the amplifier. Use an appropriate gauge wire (e.g., 4 AWG for this amplifier) and install an in-line fuse holder within 18 inches of the battery.
- Art (GND): Connect a wire of the same gauge as the power wire from the GND terminal on the ampl-alimentatur ma' wiċċ tal-metall nadif u mhux miżbugħ fuq ix-chassis tal-vettura. Kun żgur li hemm konnessjoni elettrika tajba.
- Remot (REM): Connect a thin wire from the remote output of your head unit (usually a blue/white wire) to the REM terminal on the amplifer. Dan il-wajer idawwar il- ampIl-lifer mixgħul u mitfi bl-unità ewlenija tiegħek.
- Input RCAQabbad il-kejbils RCA mill-pre- tal-unità ewlenija tiegħekamp outputs to the corresponding RCA input jacks on the amplifier. Ensure correct channel matching (Front, Rear, Subwoofer).
- Riżultati tal-Ispeaker: Connect your speakers to the amplifier's speaker terminals. Pay close attention to polarity (+ and -) for each speaker. Ensure the total impedance of your speakers matches the amplifier's stable impedance (2 Ohm stereo stable).
5. Istruzzjonijiet Operattivi
Once installed, you can adjust the amplifier settings to optimize your audio system's performance.
5.1 Gwadan Kontroll
Il-kontroll tal-qligħ (LEVEL) jaqbel mal- amplifier's input sensitivity to the output of your head unit. Start with the gain set to minimum. Play a familiar track at about 75% of your head unit's maximum volume. Slowly increase the amplifier's gain until you hear distortion, then back off slightly. Do not use the gain control as a volume knob.
5.2 Issettjar tal-Crossover
- Filtru Pass Għoli (HPF): Used for full-range speakers (front/rear channels). This filter allows frequencies above the set point to pass through. Adjust to prevent low frequencies from distorting smaller speakers. Typical settings range from 80Hz to 120Hz.
- Filtru tal-Pass Baxx (LPF): Used for subwoofers (subwoofer channel). This filter allows frequencies below the set point to pass through. Adjust to match the subwoofer's frequency response and blend with your main speakers. Typical settings range from 80Hz to 100Hz.
5.3 Bass Boost
The bass boost control allows you to enhance low frequencies. Use this feature sparingly, as excessive bass boost can lead to distortion and potential speaker damage. Adjust in small increments (0/+6/+12 dB) using the included remote control.
6. Manutenzjoni
- Żomm il- ampIl-lavatur ikun nadif u ħieles mit-trab. Uża drapp artab u niexef għat-tindif.
- Tiżgura ventilazzjoni xierqa madwar il- amplifier biex jipprevjeni sħana żejda.
- Iċċekkja perjodikament il-konnessjonijiet tal-wajers kollha għal issikkar u korrużjoni.
7 Issolvi l-problemi
| Problema | Kawża Possibbli | Soluzzjoni |
|---|---|---|
| No Power / Protection LED On | Blown fuse, poor power/ground connection, amplifier fil-mod ta 'protezzjoni. | Iċċekkja l-fjus in-line u amplifier fuses. Verify power, ground, and remote wire connections. Check speaker wiring for shorts. |
| Ebda Ħoss | RCA cables disconnected, gain too low, head unit settings, speaker wires disconnected. | Check RCA connections. Adjust gain. Verify head unit output. Check speaker wire connections. |
| Ħoss Mgħawġ | Gain set too high, improper crossover settings, speaker impedance mismatch, damaged speakers. | Reduce gain. Adjust HPF/LPF settings. Verify speaker impedance. Inspect speakers for damage. |
| AmpTisħin żejjed tal-lifer | Ventilazzjoni insuffiċjenti, tagħbija ta' impedenza baxxa, użu fit-tul ta' volum għoli. | Kun żgur li l-arja tiċċirkola sew madwar amplifer. Iċċekkja l-impedenza tal-ispiker. Naqqas il-volum jew ħalli amplifier biex jiksaħ. |
8. Speċifikazzjonijiet
| Karatteristika | Speċifikazzjoni |
|---|---|
| Numru tal-Mudell | DX1800.5 |
| Brand | Matriċi |
| Numru ta 'Kanali | 5 |
| Output ta 'Qawwa Max | 1800 Watts |
| Qawwa RMS (4 Ohm) | 125W x 4 Ch. + 480W x 1 Ch. |
| Qawwa RMS (2 Ohm) | 250W x 4 Ch. + 800W x 1 Ch. |
| Provvista tal-Enerġija | PWM DC to DC |
| Stereo Stability | 2 Ohm Stabbli |
| Filtru Pass Għoli (HPF) | Variable 40 Hz - 3 kHz |
| Filtru tal-Pass Baxx (LPF) | Variable 40 Hz - 250 Hz |
| Boost Boost | 0/+6/+12 dB (Selectable) |
| Separazzjoni tal-Kanal | > 60 dB |
| Dimensjonijiet tal-Prodott (L x W x H) | 16.3 x 9.7 x 2 pulzieri (41.4 x 24.6 x 5.1 ċm) |
| Piż tal-Prodott | 3.2 kg (7.05 lbs) |
| Konformità | CE, RoHS, FCC |
| UPC | 793276301031 |
9. Garanzija u Appoġġ
For warranty information and technical support, please refer to the warranty card included with your product or visit the official Matrix websit. Żomm il-prova tax-xiri tiegħek għal talbiet ta' garanzija.
For further assistance, you may contact Matrix customer support through their official channels.
