Introduzzjoni
The Westek TMDCD60 is a hardwire indoor countdown timer designed to replace a standard wall switch. It provides timed control for lights, fans, heaters, and other devices, automatically turning them off after a selected duration. This manual provides instructions for safe installation, operation, and maintenance of your timer switch.
Informazzjoni dwar is-Sigurtà
TWISSIJA: Riskju ta' Xokk Elettriku. Improper installation can lead to serious injury or death. Always turn off power at the circuit breaker or fuse box before beginning installation. Consult a qualified electrician if you are unsure about any part of the installation process.
- Dan l-apparat huwa għal użu fuq ġewwa biss.
- Kun żgur li l-konnessjonijiet kollha tal-wajers huma sikuri u jikkonformaw mal-kodiċijiet elettriċi lokali.
- Do not exceed the electrical ratings of the device.
- A neutral wire is required for installation. Older homes may not have a neutral wire in the switch box.
Kontenut tal-Pakkett
- Westek TMDCD60 Countdown Timer Switch
- Manwal ta 'Istruzzjoni (dan id-dokument)
Prodott Overview
The Westek TMDCD60 timer switch features a single push-button control and LED indicators for selected time settings. It is designed to fit into a standard wall switch box and can be used with a standard rocker wallplate (not included).
Figura 1: Quddiem view of the TMDCD60 timer switch. The face includes a single control button and five LED indicators labeled "10 MIN", "20 MIN", "30 MIN", "60 MIN", and "HOLD".
Installazzjoni
- Itfi l-Enerġija: Locate the circuit breaker or fuse that controls the switch you are replacing. Turn off the power completely before proceeding. Verify power is off using a voltagtester.
- Neħħi Swiċċ Eżistenti: Carefully remove the wallplate and unscrew the existing switch from the wall box. Disconnect the wires from the old switch. Note the connections for reference.
- Identifika l-Wajers: The Westek TMDCD60 timer requires four wires:
- Wajer Iswed: Hot (Line)
- Wajer Aħmar: Load (to the device being controlled)
- Wajer abjad: Newtrali
- Wajer Aħdar: Art
Ensure your wall box contains a neutral wire. If not, this timer cannot be installed without running a new neutral wire, which should be done by a qualified electrician.
Figura 2: Lura view of the TMDCD60, illustrating the labeled wires for proper connection.
- Qabbad Wajers: Using wire nuts (not included), connect the wires from the wall box to the corresponding wires on the TMDCD60 timer switch:
- Qabbad il- Iswed wajer mit-tajmer għall- Hot (Line) wire from the wall box.
- Qabbad il- Aħmar wajer mit-tajmer għall- Tagħbija wire from the wall box (to the light/fan).
- Qabbad il- Abjad wajer mit-tajmer għall- Newtrali wire from the wall box.
- Qabbad il- Aħdar wajer mit-tajmer għall- Art wire from the wall box.
- Immonta t-Tajmer: Carefully fold the wires into the wall box. The timer is deeper than a standard switch, so ensure there is enough space. Secure the timer switch to the wall box using the provided screws.
- Installa l-Wallplate: Attach a standard rocker wallplate (not included) over the timer switch.
- Irrestawra l-Enerġija: Erġa' ixgħel il-kurrent mis-circuit breaker jew mill-kaxxa tal-fjużijiet.
Operazzjoni
The TMDCD60 timer operates with a single push-button control. Each press cycles through the available countdown settings and the HOLD function.
- Turning On and Setting Timer: Press the control button once to activate the timer. The timer will cycle through the following settings with each subsequent press:
- OFF (no LED lit)
- 10 Minutes (10 MIN LED lights up)
- 20 Minutes (20 MIN LED lights up)
- 30 Minutes (30 MIN LED lights up)
- 60 Minutes (60 MIN LED lights up)
- HOLD (HOLD LED lights up)
The connected device will remain on for the selected duration and then automatically turn off. The corresponding LED will indicate the active setting.
- Funzjoni HOLD: To keep the connected device on indefinitely, press and hold the control button for approximately one second until the "HOLD" LED illuminates. In HOLD mode, the device will remain on until you press the button again to turn it off or select a countdown setting.
- Itfi: To turn off the connected device before the countdown finishes or while in HOLD mode, press the control button until no LEDs are lit.
Manutenzjoni
The Westek TMDCD60 timer switch requires minimal maintenance. To clean the surface, wipe with a soft, damp drapp. Tużax prodotti tat-tindif jew solventi li joborxu. Kun żgur li l-elettriku jkun mitfi qabel ma tnaddaf.
Issolvi l-problemi
| Problema | Kawża Possibbli | Soluzzjoni |
|---|---|---|
| It-tajmer ma jixgħelx jew ma jaħdimx. | L-ebda enerġija fis-swiċċ. Wajers mhux korretti. | Iċċekkja l-interruttur jew il-fjus. Verify all wiring connections are correct as per the Installation section. Ensure a neutral wire is connected. |
| Connected device does not turn off after selected time. | Timer is in HOLD mode. Wajers mhux korretti. | Press the button to cycle out of HOLD mode. Recheck load wire connection. |
| L-indikaturi LED mhumiex qed jaħdmu. | L-ebda enerġija fis-swiċċ. Ħsara fl-unità. | Iċċekkja l-provvista tal-enerġija. If power is present and wiring is correct, the unit may be faulty. Contact customer support. |
Speċifikazzjonijiet
- Mudell: TMDCD60
- Ditta: Westek
- Kulur: Abjad
- Input Voltage: 120V AC, 60Hz
- Tagħbija Massima: 15A Resistive, 1000W Tungsten, 500VA Ballast, 1/4 HP Motor
- Issettjar tat-Timer: 10, 20, 30, 60 minutes, HOLD
- Dimensjonijiet: 1"D x 1"W x 1"H (Note: These dimensions typically refer to packaging; the device itself is deeper for in-wall installation.)
- Piż tal-oġġett: 4.48 uqija
- Tip ta 'Immuntar: Ħajt
- Stil Swiċċ: Rocker Switch
- Wajer newtrali: Meħtieġa
Garanzija u Appoġġ
This Westek product is covered by a Garanzija limitata ta 'sena mid-data tax-xiri. Din il-garanzija tkopri difetti fil-materjali u l-abbilità taħt użu normali.
For technical support or warranty claims, please contact Westek customer service. You can find more information and contact details on the official Westek webis-sit jew billi żżur il- Westek Store on Amazon.
