Brady 480/600V Clamp-Manwal ta' Istruzzjonijiet għall-Imblukkar tal-Breaker

1. Prodott Aktarview

The Brady 480/600V Clamp-On Breaker Lockout (Model 65966) is a critical safety device designed to prevent accidental energization of electrical circuits during maintenance or service. This lockout device ensures compliance with OSHA 1910.147 standards for lockout/tagout procedures, providing a secure method to isolate energy sources.

It features a new blade design for a tighter grip and includes detachable cleats to expand its compatibility with various circuit breakers. Made of rugged polypropylene and impact-modified nylon, it is built for durability in industrial environments.

Image 1: The Brady 480/600V Clamp-On Breaker Lockout device, showing its red body and black thumb screw mechanism.

2. Informazzjoni dwar is-Sigurtà

WARNING: Always follow established Lockout/Tagout (LOTO) procedures as per OSHA 1910.147 standards. This device is intended to supplement, not replace, proper energy isolation procedures. Ensure all energy sources are de-energized and verified before applying this lockout device.

• Verify the circuit breaker is in the "OFF" position before applying the lockout device.
• Always attach a padlock and a worker's protective tag (e.g., "DANGER DO NOT OPERATE") to the lockout device.
• Ensure the lockout device is securely fastened and cannot be easily removed without the key to the padlock.
• Only authorized personnel should apply and remove lockout devices.

3. Setup u Installazzjoni

Follow these steps to properly install the Brady Clamp-On Breaker Lockout:

1. De-energize the Circuit: Ensure the circuit breaker is in the "OFF" position and the circuit is completely de-energized. Verify zero energy state using appropriate testing equipment.
2. Position the Lockout Device: Poġġi l-clamp-on lockout device over the circuit breaker switch tongue. The device is designed to fit snugly over the breaker handle.
3. Assigura l-Apparat: Rotate the black thumb wheel clockwise to tighten the device onto the circuit breaker switch. Continue turning until the lockout device is securely fastened and cannot be moved from the "OFF" position.
4. Attach Padlock and Tag: Once the lockout device is secure, attach a padlock through the designated hole on the device. Then, attach a worker's protective tag (e.g., "DANGER DO NOT OPERATE") to the padlock or the device itself.

Image 2: The Brady Clamp-On Breaker Lockout securely installed on a circuit breaker, with a padlock and a "DANGER LOCKED OUT" tag mehmuża.

Using Detachable Cleats: The lockout device includes detachable cleats that can be used to accommodate a wider range of circuit breaker sizes and types. If the standard fit is not secure, attach the appropriate cleats to the device before installation as described above.

Gwida tal-Vidjow tal-Installazzjoni

4. Istruzzjonijiet Operattivi

The primary operation of this device is to facilitate safe lockout/tagbarra proċeduri.

4.1. Applying Lockout

1. Ensure the equipment is shut down and the circuit breaker is in the "OFF" position.
2. Follow the installation steps outlined in Section 3 to securely attach the lockout device.
3. Attach your personal padlock and a "DANGER DO NOT OPERATE" tag.
4. Verify that the circuit breaker cannot be moved to the "ON" position with the lockout device and padlock in place.

4.2. Removing Lockout

1. Only the authorized person who applied the lockout device should remove it.
2. Remove the padlock and the protective tag.
3. Rotate the thumb wheel counter-clockwise to loosen the lockout device.
4. Carefully remove the lockout device from the circuit breaker.
5. Before re-energizing, ensure all personnel are clear and the equipment is safe to operate.

5. Manutenzjoni

To ensure the longevity and effectiveness of your Brady Clamp-On Breaker Lockout, follow these maintenance guidelines:

• Spezzjoni regolari: Before each use, visually inspect the device for any signs of wear, cracks, damage, or deformation. Check the thumb wheel for smooth operation and ensure it tightens securely.
• Tindif: Clean the device with a mild soap and water solution if necessary. Avoid harsh chemicals or abrasive cleaners that could damage the polypropylene and nylon materials.
• Ħażna: Store the lockout device in a clean, dry place away from direct sunlight and extreme temperatures when not in use.
• Sostituzzjoni: If any damage is observed, or if the device no longer secures properly, replace it immediately to maintain safety standards.

6 Issolvi l-problemi

If you encounter issues with your Brady Clamp-On Breaker Lockout, consider the following:

• L-Apparat Ma Joqgħodx: Ensure you are using the correct size lockout device for your circuit breaker. This model (65966) is designed for 480/600V breakers. Utilize the included detachable cleats if the standard fit is loose or unstable.
• Thumb Wheel Not Tightening: Check for any debris or obstruction in the thumb wheel mechanism. Ensure the device is correctly aligned over the breaker switch tongue. If the thumb wheel spins freely without tightening, the device may be damaged and should be replaced.
• Padlock Does Not Fit: This device accepts lock shackles up to 9/32 inches (approximately 7.14 mm) in diameter. Ensure your padlock shackle meets this specification.

For further assistance, please contact Brady customer support.

7. Speċifikazzjonijiet

8. Garanzija u Appoġġ

For specific warranty information regarding your Brady 480/600V Clamp-On Breaker Lockout, please refer to the documentation included with your purchase or visit the official Brady website. Brady products are designed for durability and compliance with safety standards.

If you require technical support, have questions about product application, or need to report an issue, please contact Brady customer service:

• Brady Official Websit: www.bradyid.com
• Irreferi għall- website for contact numbers and support resources in your region.