AmpManwal tal-Utent tat-Tester tal-Kejbils LAN robe LAN-1

1. Introduzzjoni

Il- Amprobe LAN-1 LAN Cable Tester is a diagnostic tool designed to identify and trace data cables and connectors. It helps detect common wiring issues such as shorts, miswirings, and open circuits in various cable types. This manual provides detailed instructions for the proper use, setup, and maintenance of your LAN-1 tester.

The LAN-1 evaluates most common cable types, including 10/100 base-T, 10 base-2, RJ45 modular, AT&T 258A, EIA/TIA 568A/568B, and Token Ring cables, as well as RJ45 and BNC connectors. It can test cables up to 300 meters long and uses LED indicators and an audible buzzer to signal cable status and errors.

2. Informazzjoni dwar is-Sigurtà

Jekk jogħġbok aqra u ifhem l-istruzzjonijiet kollha tas-sigurtà qabel ma tħaddem Amprobe LAN-1 LAN Cable Tester. Failure to follow these instructions may result in injury or damage to the device.

Do not use the device if it appears damaged or is not operating correctly.
Ensure the correct battery type and polarity are used during installation.
Evita li tesponi l-apparat għal temperaturi estremi, umdità, jew dawl tax-xemx dirett.
Tippruvax issewwi jew timmodifika l-apparat int stess. Irreferi għal kull manutenzjoni f'idejn persunal kwalifikat.
Always disconnect the cable tester from any active network or power source before performing maintenance or battery replacement.

3. Kontenut tal-Pakkett

Iċċekkja li l-oġġetti kollha elenkati hawn taħt huma preżenti fil-pakkett tiegħek:

LAN-1 LAN Cable Tester
(1) Remote terminator
(1) RJ45 to female BNC cable
(1) RJ45 to male BNC cable
(1) RJ45 to RJ45 cable
(1) Female BNC to female BNC cable
(1) 9V battery (installed)
Istruzzjonijiet (dan il-manwal)

4. Prodott Aktarview

Il- Amprobe LAN-1 features a compact design with intuitive controls and clear LED indicators for efficient cable testing.

4.1 Karatteristiċi ewlenin

Cable Testing: Locates and traces data cables and connectors to identify shorts, miswiring, and opens.
Kompatibilità versatili: Evaluates 10/100 base-T, 10 base-2, RJ45 modular, AT&T 258A, EIA/TIA 568A/568B, and Token Ring cables, along with RJ45 and BNC connectors.
Indikazzjoni ta' Żball: An audible buzzer indicates an error condition in the cable.
Medda Estiża: Tests cables up to 300 meters long.
Wirja ċara: Eighteen red and green LEDs indicate the source or test results.
Modi tat-Test: Supports Loopback Test and Remote Test functions.
Konformità tas-Sigurtà: CE - EMC certified.

4.2 Identifikazzjoni tal-Komponent

Amprobe LAN-1 LAN Cable Tester front view

Figura 1: Quddiem view tal- Amprobe LAN-1 LAN Cable Tester. This image displays the main unit with its LED pin-out indicator, battery status light, and control buttons including AUTO, MAN, HOLD, TEST, BATT, and the power button.

Amprobe LAN-1 LAN Cable Tester with remote terminator

Figura 2: Amprobe LAN-1 LAN Cable Tester showing the main unit and the remote terminator module. This view highlights how the remote unit connects to the main tester for comprehensive cable testing.

LEDs INDIKATURI TAL-PIN-OUT: Displays the wiring status for each pin (1-8) and ground (G).
BATT LED: Jindika l-istatus tal-batterija.
Buttuna AUTO: Initiates automatic scanning of cable pins.
MAN Button: Allows manual step-through of cable pins.
Buttuna ŻOMM: Pauses the current test result display.
Buttuna TEST: Starts a test cycle.
POWER Button (Yellow): Ixgħel u jitfi l-apparat.
Port RJ45: For connecting RJ45 cables.
Port tal-BNC: For connecting BNC cables.
Remote Terminator: A separate module used for testing installed cables or long runs.

5. Setup

5.1 Installazzjoni tal-batterija

The LAN-1 tester is powered by one 9V battery, which is typically pre-installed. If replacement is needed:

Kun żgur li l-apparat ikun mitfi.
Sib l-għatu tal-kompartiment tal-batterija fuq wara tal-unità prinċipali.
Remove the screw(s) securing the cover and carefully open it.
Remove the old 9V battery and disconnect it from the terminals.
Connect a new 9V battery, ensuring correct polarity (+ to + and - to -).
Poġġi l-batterija fil-kompartiment u erġa’ poġġi l-għatu, billi twaħħlu bil-vit(i).

The battery provides power for up to 20 hours of testing.

5.2 Kejbils tal-Konnessjoni għall-Ittestjar

Before testing, ensure the cable is disconnected from any active network equipment.

For patch cables (short cables not installed in walls): Connect one end of the cable to the RJ45 or BNC port on the main unit and the other end to the corresponding port on the remote terminator.
For installed cables (e.g., wall plates, patch panels): Connect one end of the cable to the RJ45 or BNC port on the main unit. Connect the remote terminator to the other end of the installed cable (e.g., at the wall plate in another room).

6. Istruzzjonijiet Operattivi

6.1 Tixgħel/Jitfi

Agħfas l-isfar QAWWA button to turn the device on. Press it again to turn the device off.

6.2 Twettiq ta' Test

Once the cable is connected, you can perform a test:

Agħfas il- TEST button to initiate a cable test.
Automatic Scan (AUTO mode): Agħfas il- AUTO button. The tester will automatically scan through each pin (1-8 and G) and display the results sequentially. This is suitable for quick checks.
Manual Scan (MAN mode): Agħfas il- Bniedem button. Each press of the Bniedem button will advance the test to the next pin, allowing for a detailed examination of each connection.
Funzjoni ta' Żomm: Agħfas il- ŻOMM button to pause the current display of the pin-out indicator. Press it again to resume scanning.

6.3 Interpretazzjoni tal-Indikaturi LED

The 18 red and green LEDs on the PIN-OUT INDICATOR provide visual feedback on the cable's status:

LED aħdar: Indicates a correct connection for the corresponding pin.
LED aħmar: Indicates an error for the corresponding pin (e.g., open circuit, short circuit, miswiring).
L-ebda LED: May indicate an open circuit or a broken wire for that pin.
Buzzer: An audible buzzer will sound when an error condition is detected, providing an additional alert.

The LEDs on the remote module will mirror the main unit's display for the corresponding pins, allowing for verification of end-to-end continuity.

6.4 Kontroll tal-Istatus tal-Batterija

Agħfas il- BATT button to check the battery level. The BATT LED will illuminate if the battery has sufficient power. If the BATT LED does not light up or is dim, replace the 9V battery.

7. Manutenzjoni

7.1 Tindif

To ensure the longevity and proper functioning of your LAN-1 tester, keep it clean and free from dust and debris.

Imsaħ il-barra tal-apparat b'artab, damp drapp. Tużax tindif jew solventi li joborxu.
Ensure no moisture enters the ports or battery compartment.

7.2 Sostituzzjoni tal-batterija

Replace the 9V battery when the BATT LED indicates low power or if the device fails to power on. Refer to Section 5.1 for detailed battery installation instructions.

Dejjem armi l-batteriji użati skont ir-regolamenti lokali.

8 Issolvi l-problemi

Jekk tiltaqa' ma' problemi bil- Amprobe LAN-1 LAN Cable Tester, refer to the following common problems and solutions:

Problema	Kawża Possibbli	Soluzzjoni
L-apparat ma jixgħelx.	Batterija baxxa jew mejta; installazzjoni ħażina tal-batterija.	Ibdel il-batterija ta' 9V, waqt li tiżgura l-polarità korretta.
No LED activity during test.	Cable not properly connected; faulty cable; remote terminator not connected.	Ensure cables are securely connected to both the main unit and remote terminator. Test with a known good cable.
Buzzer sounds continuously or unexpectedly.	Short circuit or severe miswiring detected.	Examine the cable for physical damage or incorrect wiring. Check connectors for bent pins.
Inconsistent test results.	Loose connections; intermittent cable fault; low battery.	Ensure all connections are tight. Replace battery. Try wiggling the cable during test to identify intermittent faults.

9. Speċifikazzjonijiet

Mudell	LAN-1
Provvista tal-Enerġija	(1) 9V battery
Ħajja tal-batterija	Up to 20 hours of tests
Tipi ta' Kejbils Ittestjati	10/100 base-T, 10 base-2, RJ45 modular, AT&T 258A, EIA/TIA 568A/568B, Token Ring cables
Cable Connector Types	RJ45 and BNC
Tul Massimu tal-Linja	300m
Piż	0.6 lb. / 0.27 kg (approx. 9.5 ounces)
Dimensjonijiet (H x W x D)	5.1 x 2.2 x 1.5 in. / 130 x 56 x 38mm
Wiri	18 LEDs (9 Red and 9 Green), 9 LEDs on Remote module
Konformità tas-Sigurtà	CE - EMC

10. Informazzjoni dwar Garanzija

Il- Amprobe LAN-1 LAN Cable Tester comes with a Garanzija Limitata ta' Sena. This warranty covers defects in materials and workmanship under normal use. It does not cover damage resulting from misuse, accident, modification, neglect, or unauthorized repair.

For specific warranty terms and conditions, please refer to the warranty card included with your product or contact Amprobe customer support.

11. Appoġġ għall-Klijent

If you have any questions, require technical assistance, or need to report a problem with your Amprobe LAN-1 LAN Cable Tester, please contact Amprobe customer support.

Jekk jogħġbok żur l-uffiċjal Amplibsa webis-sit għall-aktar informazzjoni ta' kuntatt u riżorsi ta' appoġġ aġġornati.

Riżorsi onlajn: www.amprobe.com

	AmpManwal tal-Utent tas-Sistema ta' Lokatur ta' Kejbils/Pajpijiet taħt l-Art robe AT-3500 Manwal komprensiv għall-utent għall- AmpSistema ta' Lokatur ta' Kejbils/Pajpijiet taħt l-Art robe AT-3500, li tiddeskrivi l-operazzjoni, il-karatteristiċi, l-ispeċifikazzjonijiet tekniċi, u l-manutenzjoni għal skoperta preċiża ta' utilitajiet taħt l-art.
	AmpManwal tal-Utent tal-Multimetru Diġitali robe AM-420 Manwal tal-utent għall- AmpMultimetru Diġitali robe AM-420, li jagħti dettalji dwar il-karatteristiċi tiegħu, il-kapaċitajiet ta' kejl, il-prekawzjonijiet ta' sigurtà, u l-ispeċifikazzjonijiet għall-ittestjar elettriku. Adattat għal użu residenzjali u professjonali.
	AmpManwal tal-Utent tat-Termometru tal-Infra-aħmar robe IR-750 / IR-750-EUR 50:1 Manwal tal-utent għall- AmpTermometri infra-aħmar robe IR-750 u IR-750-EUR 50:1. Il-karatteristiċi jinkludu firxa wiesgħa ta' temperatura, preċiżjoni għolja, pointer tal-lejżer, reġistrazzjoni tad-dejta, u konnettività USB għal applikazzjonijiet industrijali u professjonali.
	AmpManwal tal-Utent tal-Miter tal-Kapaċità u r-Reżistenza robe CR50A Dan il-manwal tal-utent jipprovdi struzzjonijiet komprensivi dwar kif tħaddem il- Amprobe CR50A Miter tal-Kapaċitanza u r-Reżistenza, li jkopri l-karatteristiċi tiegħu, il-proċeduri tal-kejl, il-linji gwida tas-sigurtà, u l-ispeċifikazzjonijiet tekniċi.
	AmpManwal tal-Istruzzjonijiet tas-Sett tal-Butt robe TT-200 - Ittestjar tal-Linja u Komunikazzjonijiet Manwal ta' struzzjonijiet komprensiv għall- Amprobe TT-200 Butt Set, li jiddeskrivi l-karatteristiċi tiegħu għall-ittestjar tal-linja, il-kejl tar-reżistenza tal-insulazzjoni, u l-komunikazzjonijiet temporanji għat-tekniċi.
	AmpGwida ta' Bidu Mgħaġġel għall-Lokatur tal-Utilitajiet taħt l-Art robe UAT-600 Gwida ta' bidu rapidu għall- AmpSerje ta' Lokaturi ta' Utilitajiet taħt l-Art robe UAT-600, li tipprovdi struzzjonijiet dwar il-lokalizzazzjoni attiva u passiva ta' utilitajiet bl-użu ta' diversi modi bħal Enerġija, Radju, Induzzjoni, Wajers tat-Test Diretti, u Sinjal Clamp.

Amprobe LAN-1