1. Introduzzjoni
The AtlasIED PSR-206 is a zone page powered relay pack designed to provide six independent relay closures for various audio and control applications. This manual provides essential information for proper installation, operation, and maintenance of the device, ensuring reliable performance and system integration.
2. Informazzjoni dwar is-Sigurtà
WARNING: Risk of electric shock. Do not open the unit. Refer all servicing to qualified personnel.
- Always disconnect power before performing any installation, maintenance, or troubleshooting procedures.
- Kun żgur li l-unità hija ertjata sew biex tevita perikli elettriċi.
- Adhere to all local and national electrical codes during installation.
- Tesponix l-unità għall-umdità jew temperaturi estremi.
- Uża biss it-tipi u l-klassifikazzjonijiet speċifikati tal-fjusis għas-sostituzzjoni.
3. Prodott Aktarview
The PSR-206 is a robust relay pack featuring six independent relays, powered by a 117 VAC input and providing a 24 VDC output. It is designed for integration into paging and control systems.
Figura 1: Fuq view of the AtlasIED PSR-206 showing power input, fuse, amplifier output, bus connections, 24 VDC output, and six external switch relay terminals.
Karatteristiċi ewlenin:
- Six independent relay closures.
- 117 VAC input power.
- 24 VDC f'1/2 AMP output for external devices.
- Integrata 1 AMP fuse for circuit protection.
- Clearly labeled screw terminals for easy wiring.
4. Speċifikazzjonijiet
| Karatteristika | Speċifikazzjoni |
|---|---|
| Numru tal-Mudell | PSR-206 |
| Input Voltage | 117 VAC |
| Ħruġ Voltage / Kurrenti | 24 VDC f'1/2 AMP |
| Numru ta' Relays | 6 |
| Fjus Rating | 1 AMP |
| Piż tal-oġġett | 6 liri |
| Dimensjonijiet tal-Pakkett | 19 x 6 x 5 pulzieri |
| Manifattur | Ħoss tal-Atlas |
| Data L-Ewwel Disponibbli | 8 ta’ Diċembru 2008 |
5. Setup u Installazzjoni
Careful installation is crucial for optimal performance. Ensure all power is disconnected before proceeding.
5.1 Immuntar
The PSR-206 can be mounted to a flat surface using appropriate screws through the mounting tabs on the unit's chassis.
5.2 Konnessjonijiet tal-Wiring
- Dħul tal-Enerġija (117 VAC): Connect the unit's power cord to a standard 117 VAC power outlet. The unit is protected by a 1 AMP fuse, accessible on the side.
- 24 VDC Output: The terminals labeled '24 VDC' (+ and -) provide a regulated 24 VDC at 1/2 AMP for powering compatible external devices. Observe polarity.
- External Switches (Relay Control): The terminals labeled 'EXTERNAL SWITCHES' (1-6) along with 'COM' (Common) are used to control the six independent relays. Connect your external control switches between the 'COM' terminal and the desired relay terminal (1 through 6). When a switch is closed, the corresponding relay will activate.
- AMP BARRA: These terminals are typically used for connecting to an amplifier's input, often for muting or other control functions during paging. Consult your amplifier's manual for specific wiring.
- OFF BUS: These terminals are for specific system bus connections, often used to signal an 'off-hook' or busy status. Refer to your overall system design for proper integration.
6. Istruzzjonijiet Operattivi
Once properly installed and wired, the PSR-206 operates automatically based on the signals received from connected external switches.
- Attivazzjoni tar-Relay: When an external switch connected to one of the 'EXTERNAL SWITCHES' terminals (1-6) and 'COM' is closed, the corresponding internal relay will activate. This closure can be used to trigger various functions in your audio or control system, such as zone paging, muting, or activating external devices.
- 24 VDC Power Supply: The 24 VDC output is continuously available when the unit is powered, providing a stable power source for low-power auxiliary equipment.
7. Manutenzjoni
The PSR-206 is designed for reliable, long-term operation with minimal maintenance.
- Tindif: Periodically clean the exterior of the unit with a soft, dry cloth. Do not use liquid cleaners or solvents.
- Sostituzzjoni tal-fjus: If the unit loses power, check the 1 AMP fuse located on the side of the unit. Disconnect power before replacing the fuse. Always replace with a fuse of the identical type and rating (1 AMP).
- Spezzjoni tal-Konnessjoni: Spezzjona l-konnessjonijiet kollha tal-wajers kull sena biex tiżgura li huma sikuri u ħielsa mill-korrużjoni.
8 Issolvi l-problemi
Irreferi għat-tabella li ġejja għal kwistjonijiet komuni u s-soluzzjonijiet potenzjali tagħhom.
| Problema | Kawża Possibbli | Soluzzjoni |
|---|---|---|
| Unit has no power / No indicator lights | No 117 VAC input; Blown 1 AMP fjus | Verify power outlet functionality. Check and replace 1 AMP fuse if necessary (ensure power is disconnected first). |
| Relay not activating when external switch is closed | Incorrect wiring; Faulty external switch; Damaged relay | Check wiring between external switch and 'COM'/'EXTERNAL SWITCHES' terminals. Test the external switch for functionality. If issue persists, professional service may be required. |
| Nru 24 VDC output | Internal fault; Overload on 24 VDC output | Ensure no short circuits or excessive load on the 24 VDC output. If the unit has power but no 24 VDC output, professional service is recommended. |
9. Garanzija u Appoġġ
For detailed warranty information, technical support, or service inquiries, please contact Atlas Sound directly. Refer to your original purchase documentation or the official Atlas Sound webis-sit għad-dettalji ta' kuntatt u t-termini tal-garanzija l-aktar riċenti.
Indirizz tal-Manifattur: 1501 Jack McKay Blvd, Ennis, TX 758HG (Information derived from product labeling)
It is recommended to register your product with Atlas Sound to ensure you receive updates and support.
