Introduzzjoni
This manual provides instructions for the installation and use of the ACV 1324-45 ISO Radio Connection Cable. This adapter is designed to facilitate the installation of an aftermarket radio in compatible Audi, Seat, Skoda, and Volkswagen vehicles, specifically those requiring phantom power for the antenna and utilizing a Quadlock connector system.
Karatteristiċi tal-Prodott
- Enables the installation of a replacement car radio.
- Includes an additional adapter for connecting antenna voltage supply to car radios.
- Compatible with all models featuring a Quadlock connector.
- Specifically designed for Audi vehicles from 2012 onwards.
- Also compatible with various Seat, Skoda, and Volkswagen models.
- Constructed from copper and plastic for durability.
Setup u Installazzjoni
The ACV 1324-45 cable simplifies the process of connecting an aftermarket car radio. Please follow these general steps for installation. Professional installation is recommended if you are unfamiliar with car audio wiring.
- Preparazzjoni tal-Vettura: Kun żgur li l-ignition tal-vettura tkun mitfija u l-batterija tkun skonnettjata qabel tibda kwalunkwe xogħol elettriku.
- Access Radio Compartment: Carefully remove the existing car radio or blanking plate to access the vehicle's wiring harness.
- Identify Vehicle Connector: Locate the vehicle's Quadlock connector. The ACV 1324-45 cable is designed to interface with this type of connector.
- Connect ACV Adapter: Connect the ACV 1324-45 adapter's vehicle-side connector to the vehicle's existing Quadlock harness. Ensure a secure fit.
- Qabbad mar-Radju Aftermarket: Connect the other end of the ACV 1324-45 adapter to the ISO connector of your new aftermarket car radio.
- Antenna Power Connection: The adapter includes a separate wire for antenna voltage supply. Connect this wire to the corresponding antenna power output on your aftermarket radio to ensure proper antenna function, especially for phantom-powered antennas.
- Verifika tal-Wajers: Double-check all connections for security and correct polarity. Some aftermarket radios or vehicle models may require minor adjustments to the power wires (e.g., swapping constant and switched 12V lines). Refer to your aftermarket radio's manual for specific wiring diagrams.
- Funzjonalità tat-Test: Reconnect the vehicle battery and test the radio's functionality, including power, audio, and antenna reception, before fully reassembling the dashboard.
Figura 1: Aktarview of the ACV 1324-45 ISO Radio Connection Cable, showing the main harness and phantom power adapter.
Figure 2: Detail of the Quadlock connector end of the ACV 1324-45 cable, which connects to the vehicle's wiring harness.
Figure 3: The ACV 1324-45 cable displaying both the vehicle-side Quadlock connector and the aftermarket radio's ISO connector, along with the antenna power line.
Istruzzjonijiet Operattivi
Once correctly installed, the ACV 1324-45 cable functions as a passive adapter, allowing your aftermarket radio to operate as intended. There are no specific operating procedures for the cable itself. Refer to your aftermarket car radio's user manual for its operational instructions.
Manutenzjoni
The ACV 1324-45 radio connection cable requires minimal maintenance. Ensure all connections remain secure and free from moisture or physical damage. Avoid bending or crimping the wires excessively during installation or when routing the cable.
Issolvi l-problemi
If you encounter issues after installing the ACV 1324-45 cable, consider the following:
- L-ebda Enerġija għar-Radju: Verify that the vehicle's battery is properly connected and charged. Check all fuse connections. Ensure the constant 12V (yellow wire) and switched 12V (red wire) connections are correctly aligned between the vehicle harness, the ACV adapter, and the aftermarket radio. Some installations may require swapping these wires.
- Riċeviment tar-Radju Fqir: Confirm that the antenna power wire from the ACV adapter is correctly connected to the aftermarket radio's antenna power output. This is crucial for phantom-powered antennas. Ensure the antenna itself is properly connected and undamaged.
- Ebda Output Awdjo: Check all speaker wire connections for proper polarity and secure fit. Ensure the aftermarket radio is correctly configured for speaker output.
- Funzjonalità intermittenti: Inspect all connections for looseness or corrosion. Ensure the cable is not pinched or damaged.
If problems persist, consult a professional car audio installer.
Speċifikazzjonijiet
| Karatteristika | Dettall |
|---|---|
| Brand | ACV |
| Numru tal-Mudell | 1324-45 |
| Dimensjonijiet tal-Prodott (L x W x H) | 23 x 7 x 4.7 ċm (9.06 x 2.76 x 1.85 pulzieri) |
| Piż | 100 gramma (0.22 lbs) |
| Materjal | Copper and Plastic |
| Tip ta' Konnettur | RF Connector (ISO to Quadlock adapter) |
| Użu Rakkomandat | Car Radio, Car Stereos |
| ASIN | B001K90KCS |
| Kodiċi Internazzjonali tal-Artiklu | 04026724006810 |
| Disponibbiltà ta' Spare Parts (UE) | 1 Sena |
Garanzija u Appoġġ
This product is manufactured by ACV. Information regarding specific warranty terms is not provided in this manual. Please refer to your point of purchase or the manufacturer's official websit għal informazzjoni dettaljata dwar il-garanzija.
Spare parts availability in the EU is indicated for 1 year from the date of purchase. For technical support or inquiries, please contact your retailer or ACV customer service.
