1. Introduzzjoni u Fuqview
Thank you for choosing the Steinel BRS 66 L Motion Sensor Bathroom Light. This high-quality luminaire is designed for automatic illumination in bathrooms and other suitable indoor/outdoor areas, offering convenience and energy efficiency. Featuring a high-frequency sensor with 360° detection, an elegant aluminum chassis, and an opal glass globe, this light is rated IP44, making it splash-proof and ideal for damp ambjenti.
Figure 1: The Steinel BRS 66 L light seamlessly integrated into a modern bathroom setting.
2. Istruzzjonijiet tas-Sigurtà
- Installazzjoni Elettrika: Installation must be carried out by a qualified electrician in accordance with national wiring regulations and local electrical codes.
- Skonnettjar tal-Enerġija: Always disconnect the power supply at the main fuse box before commencing any installation, maintenance, or repair work.
- Voltage: Tiżgura l-provvista voltage matches the specifications of the luminaire.
- Klassifikazzjoni IP44: This product is rated IP44, meaning it is protected against solid objects over 1mm and against splashing water from any direction. It is suitable for bathroom zones 2 and 3. Do not install in bathroom zone 1 (directly above bath/shower).
- Tip ta' bozza: Use only G9 halogen bulbs with a maximum wattage ta' 40W. Teċċedix il-wat speċifikattage.
- Sħana: Halogen bulbs generate heat. Ensure adequate ventilation and do not cover the luminaire.
3. Kontenut tal-Pakkett
Please check that all parts are present and undamaged:
- Steinel BRS 66 L Luminaire (with integrated sensor)
- Ħardwer tal-immuntar (viti, tappijiet tal-ħajt)
- Manwal ta' Istruzzjoni
4. Setup u Installazzjoni
Segwi dawn il-passi għal installazzjoni sikura u korretta:
- Ipprepara għall-Installazzjoni: Kun żgur li l-provvista ewlenija tal-enerġija għaż-żona tal-installazzjoni tkun mitfija mis-circuit breaker.
- Immuntar tal-Bażi: Mark the drilling points on the wall or ceiling using the luminaire's base as a template. Drill holes and insert the provided wall plugs. Secure the luminaire's mounting base to the surface using the screws.
- Wiring: Connect the electrical wires (Live, Neutral, Earth) from your mains supply to the corresponding terminals on the luminaire's terminal block. Ensure all connections are secure and correctly insulated.
- Attach the Luminaire Body: Carefully attach the main body of the luminaire to the mounting base, ensuring it is securely fastened.
- Daħħal Basal: Gently insert two G9 halogen bulbs (max. 40W each) into their respective sockets.
- Attach Glass Globe: Carefully place the opal glass globe over the bulbs and secure it according to the fixture's design (e.g., by twisting or using retaining clips).
- Irrestawra l-Enerġija: Once installation is complete and all parts are securely in place, restore power at the circuit breaker.
Figure 2: The high-frequency sensor provides 360° detection, indicated by the wave pattern.
Figure 3: Key features of the BRS 66 L, including its high-frequency sensor and IP44 protection.
5. Istruzzjonijiet Operattivi
The Steinel BRS 66 L features an integrated high-frequency motion sensor for automatic operation.
- Awtomatiku mixgħul/mitfi: Once power is supplied, the light will automatically turn on when motion is detected within its 360° detection zone and turn off after a set delay when no further motion is detected.
- Aġġustament tas-Sensor: The sensor's sensitivity (reach) and twilight threshold (when the light should activate based on ambient light) can be adjusted. These adjustments are typically made via small dials or switches located on the sensor unit, often accessible by carefully removing the glass globe. Refer to the detailed diagrams in the full manual for precise locations.
- Poġġiment ottimali: For best performance, ensure the light is placed where its 360° detection field is not obstructed by large objects.
6. Manutenzjoni
- Tindif: To clean the luminaire, ensure the power is disconnected. Use a soft, damp drapp. Tużax prodotti tat-tindif jew solventi li joborxu, għax dawn jistgħu jagħmlu ħsara lill-finitura jew lill-ħġieġ.
- Sostituzzjoni tal-bozza: If a bulb fails, disconnect the power supply. Carefully remove the glass globe and then the faulty G9 bulb. Insert a new G9 halogen bulb (max. 40W). Reattach the glass globe and restore power.
- Kontrolli regolari: Periodically check the mounting screws for tightness and the electrical connections for any signs of wear or damage.
7 Issolvi l-problemi
| Problema | Kawża Possibbli | Soluzzjoni |
|---|---|---|
| Id-dawl ma jixgħelx. | Ebda provvista ta 'enerġija. Bozza difettuża. Sensor settings incorrect (e.g., twilight threshold too high). | Iċċekkja s-circuit breaker u l-wajers. Ibdel il-bozza. Adjust sensor's twilight setting. |
| Id-dawl jibqa' mixgħul kontinwament. | Mozzjoni kostanti skoperta. Sensor difettuż. Żball fil-wajers. | Check for continuous movement in detection zone. Contact customer support if sensor is suspected faulty. Ivverifika l-konnessjonijiet tal-wajers. |
| Light turns on too frequently/not frequently enough. | Sensor sensitivity (reach) set too high/low. | Adjust the sensor's sensitivity dial to decrease or increase detection range. |
| Teptip ħafif. | Konnessjoni maħlula. Bozza inkompatibbli. Fluttwazzjonijiet tal-qawwa. | Iċċekkja l-konnessjonijiet tal-wajers. Ensure correct G9 halogen bulb is used. Consult an electrician if power fluctuations are suspected. |
8. Speċifikazzjonijiet
| Karatteristika | Speċifikazzjoni |
|---|---|
| Numru tal-Mudell | BRS 66 |
| Brand | Steinel |
| Indiċi tal-Protezzjoni | IP44 |
| Materjal | Aluminum chassis, Opal glass globe |
| Tip Finish | Chrome |
| Numru ta' Basal | 2 |
| Max. Electrical Power | 40 Watts per bulb (Total 80W) |
| Tip ta' bozza | Aloġenu |
| Tip ta ’sokit | G9 |
| Karatteristiċi tal-Basla | Awtomatiku mixgħul/mitfi |
| Tip tas-Sensor | High-frequency motion sensor |
| Angolu ta 'skoperta | 360° |
| Użi Speċifiċi | Indoor and Outdoor (Bathroom, Hallway, etc.) |
| Piż tal-Prodott | 1.28 kg |
9. Garanzija u Appoġġ
Steinel products are manufactured to the highest quality standards. For information regarding the warranty period and terms, please refer to the documentation provided with your purchase or visit the official Steinel website. For technical support, spare parts, or service inquiries, please contact your local Steinel dealer or customer service department. Always provide the model number (BRS 66) when seeking support.