1. Introduzzjoni
This manual provides comprehensive instructions for the installation, operation, and maintenance of your Kuryakyn 7513 LED Mirror Lights. These lights are designed to enhance visibility and provide an amber accent to your 2001-2017 Honda GL1800 motorcycle (excluding F6B models).
Jekk jogħġbok aqra dan il-manwal bir-reqqa qabel l-installazzjoni u l-użu biex tiżgura l-funzjonament xieraq u s-sigurtà.
2. Informazzjoni dwar is-Sigurtà
TWISSIJA:
- Always disconnect the motorcycle's battery before performing any electrical work to prevent electrical shock or damage.
- Kun żgur li l-konnessjonijiet tal-wajers kollha huma sikuri u iżolati sew biex tevita short circuits.
- Improper installation may result in damage to the product or motorcycle, and could void the warranty.
- Consult a qualified motorcycle technician if you are unsure about any part of the installation process.
- This product is intended for use on 2001-2017 Honda GL1800 models (excluding F6B). Compatibility with other models is not guaranteed.
3. Kontenut tal-Pakkett
Iċċekkja li l-oġġetti kollha huma preżenti qabel tibda l-installazzjoni:
- (2) Kuryakyn 7513 LED Mirror Lights
- Istruzzjonijiet għall-Installazzjoni (dan il-manwal)
Figura 1: Kuryakyn 7513 LED Mirror Lights. This image shows the two LED mirror light units with their wiring harnesses, ready for installation.
4. Għodod Meħtieġa
The following tools are suggested for a smooth installation:
- Tornavit Phillips
- Stripper wajer
- Soldering supplies (solder, soldering iron)
- Tejp elettriku jew tubi li jinxtorbu bis-sħana
- Multimetru (mhux obbligatorju, għall-verifika tal-konnessjonijiet)
5. Istruzzjonijiet ta 'installazzjoni
These LED mirror lights are designed for hard-wire installation. If you have additional Kuryakyn front turn signal accent lighting with a plug-and-play harness, the installation may be simplified. This guide focuses on the hard-wire method.
5.1 Preparazzjoni
- Park your motorcycle on a level surface and ensure the engine is off and cool.
- Disconnect the negative terminal of the motorcycle's battery to prevent accidental electrical shorts.
- Carefully remove any fairing components or mirror housings necessary to access the mirror assembly and wiring. Refer to your motorcycle's service manual for specific removal procedures.
5.2 Mounting the LED Lights
- Clean the surface where the LED mirror lights will be mounted on the mirror housing. Ensure it is free of dirt, grease, and wax.
- Peel the backing from the 3M adhesive tape on the back of each LED mirror light.
- Carefully position each LED light into the gap between the mirror and the mirror housing. The slim design ensures they do not interfere with the viewable mirror surface. Press firmly to ensure good adhesion.
Figura 2: Kuryakyn LED Mirror Light installed on a motorcycle mirror, showing the amber illumination. The lights are positioned along the edge of the mirror housing.
5.3 Konnessjonijiet tal-Wiring
The Kuryakyn 7513 LED Mirror Lights require hard-wire connection to the motorcycle's existing turn signal wiring. These lights are designed to illuminate with an amber glow.
- Route the wiring from each LED mirror light to an accessible location near the motorcycle's turn signal wiring harness. Secure the wires to prevent chafing or interference with moving parts.
- Identify the positive (+) and negative (-) wires for the turn signal on your motorcycle. Typically, the positive wire will carry a pulsed voltage when the turn signal is activated, and the negative wire will be a ground. Refer to your motorcycle's wiring diagram for precise identification.
- Carefully strip a small section of insulation from the motorcycle's turn signal positive wire and the ground wire.
- Strip a small section of insulation from the wires of the Kuryakyn LED mirror light.
- Connect the positive wire from the LED mirror light to the motorcycle's turn signal positive wire.
- Connect the negative wire from the LED mirror light to the motorcycle's ground wire.
- Secure all connections using soldering and then insulate them thoroughly with electrical tape or heat shrink tubing to protect against moisture and vibration.
- Repeat the wiring process for the other LED mirror light on the opposite side of the motorcycle.
5.4 Pass Finali
- Once all wiring is complete and secured, reconnect the negative terminal of the motorcycle's battery.
- Test the LED mirror lights by activating the turn signals. Ensure both lights illuminate correctly with an amber glow.
- Carefully reassemble any fairing components or mirror housings that were removed. Ensure all fasteners are tightened to factory specifications.
6. Operazzjoni
The Kuryakyn 7513 LED Mirror Lights operate in conjunction with your motorcycle's existing turn signal system. When the turn signal is activated, the corresponding LED mirror light will illuminate with an amber glow, providing additional visibility to other road users.
These lights are designed to be a supplementary safety feature, increasing your motorcycle's conspicuity, especially during turns or lane changes.
7. Manutenzjoni
The Kuryakyn 7513 LED Mirror Lights require minimal maintenance.
- Tindif: Clean the LED lenses periodically with a soft, damp cloth and mild soap. Avoid abrasive cleaners or solvents that could damage the lens material.
- Spezzjoni: Periodically inspect the wiring and connections for any signs of wear, corrosion, or damage. Ensure the lights remain securely attached to the mirror housing.
- Kontroll tal-Funzjonalità: Regularly check that both LED mirror lights are functioning correctly when the turn signals are activated.
8 Issolvi l-problemi
| Problema | Kawża Possibbli | Soluzzjoni |
|---|---|---|
| LED lights do not illuminate. |
|
|
| Id-dwal jitteptep jew huma baxxi. |
|
|
| Lights do not adhere properly. |
|
|
9. Speċifikazzjonijiet
| Karatteristika | Dettall |
|---|---|
| Numru tal-Mudell | 7513 |
| Brand | Kuryakyn |
| Kompatibilità | 2001-2017 Honda GL1800 Models (Except F6B) |
| Tip Dawl | Dwal tal-Aċċent LED |
| Kulur Dawl | Ambra |
| Tip ta' Installazzjoni | Hard-wire (or plug-and-play with additional Kuryakyn accessories) |
| Dimensjonijiet (madwar) | 7 x 6 x 3 inches (Product Package) |
| Piż (madwar) | 2.72 uqija |
10. Garanzija u Appoġġ
Kuryakyn products are manufactured to high-quality standards. For specific warranty information, please refer to the warranty card included with your product or visit the official Kuryakyn websit.
For technical support, troubleshooting assistance, or to inquire about replacement parts, please contact Kuryakyn customer service through their official webis-sit jew l-informazzjoni ta' kuntatt ipprovduta max-xiri tiegħek.
