1. Introduzzjoni
This manual provides detailed instructions for the proper installation, operation, and maintenance of your Lanzar VIBE211 Vibe 360 Watt 2 Channel Mosfet Amplifier. Please read this manual thoroughly before attempting to install or operate the amplifier to ensure optimal performance and safety.
2. Informazzjoni dwar is-Sigurtà
Dejjem osserva l-prekawzjonijiet ta' sigurtà li ġejjin waqt l-installazzjoni u t-tħaddim:
- Disconnect the vehicle's negative battery terminal before any wiring connections are made.
- Kun żgur li l-wajers kollha huma mgħoddija u mwaħħlin sew biex tevita ħsara jew short circuits.
- Uża wajers ta' daqs xieraq għall-konnessjonijiet tal-enerġija u tal-art kif speċifikat fit-taqsima tal-installazzjoni.
- Immonta l- ampŻomm l-alimentatur sew f'post li jippermetti ventilazzjoni adegwata u li jkun protett mill-umdità u s-sħana eċċessiva.
- Tħaddimx il- ampLifter jekk ikun bil-ħsara jew ma jaħdimx sew. Irreferi għat-taqsima tas-soluzzjoni tal-problemi jew fittex assistenza professjonali.
3. Prodott Aktarview
The Lanzar VIBE211 is a 2-channel Mosfet amplifier designed for car audio systems. It features a bridgeable design, allowing for flexible configuration, and incorporates a regulated Mosfet power supply for stable performance. Key features include variable high/low pass crossover controls and a remote subwoofer bass control.
Angolat view of the silver Lanzar VIBE211 Vibe 360 Watt 2 Channel Mosfet Amplifier, wirjaasing its finned heatsink design, RCA inputs, and control panel. The amplifier features text indicating 'bridgeable 2 channel amplifier', 'vibe 211', 'Lanzar vibe', '360 watts', 'high/low pass crossover', and 'regulated mosfet power supply'. A small, separate remote bass level control unit is visible in the foreground.
4. Setup u Installazzjoni
4.1 Immuntar tal- Ampaktar ħaj
Choose a secure mounting location that provides adequate air circulation around the amplifier's heatsink. Avoid mounting in direct sunlight or areas prone to moisture. Use the provided mounting hardware to secure the amplifier firmly to a solid surface.
4.2 Konnessjonijiet tal-Wiring
Ensure all connections are tight and properly insulated to prevent short circuits.
- Power (B+): Connect a heavy-gauge wire (e.g., 8 AWG or larger) directly from the positive terminal of the vehicle's battery to the amplifier's B+ terminal. Install an appropriate fuse (15A) within 18 inches of the battery.
- Art (GND): Connect a heavy-gauge wire of the same size as the power wire from the amplifier's GND terminal to a clean, unpainted metal surface of the vehicle chassis. Ensure a good electrical connection.
- Remot (REM): Connect a smaller gauge wire (e.g., 18 AWG) from the ampIt-terminal REM tal-lifer mal-output tal-mixgħul remot tal-unità ewlenija tiegħek. Dan il-wajer jixgħel il- amplifier mixgħul u mitfi bl-istereo tiegħek.
- Input RCA: Connect the RCA audio cables from your head unit's pre-amp outputs għall- amplifier's Gold RCA Inputs. The amplifier includes Line Outs for Left and Right Channels for daisy-chaining to other ampliifikaturi.
- Riżultati tal-Ispeaker: Connect your speakers to the amplifier's speaker terminals. Observe correct polarity (+ to + and - to -). The amplifier is 2 Ohm stereo stable and bridgeable at 4 Ohms.
- Remote Subwoofer Bass Control: Connect the remote bass control unit to the designated port on the amplifier. Mount the control unit in an accessible location for easy adjustment.
5. Istruzzjonijiet Operattivi
5.1 Qawwa Inizjali
After all connections are made, reconnect the vehicle's negative battery terminal. Turn on your head unit. The amplifier features Soft Turn On/Off circuitry to prevent pops and clicks. Power Protection LED Indicators will illuminate to show operational status.
5.2 Adjusting Input Level Controls
Il- amplifier has Variable Input Level Controls. Start with the amplifier's input level set to minimum. Play a familiar piece of music through your head unit at about 75% of its maximum volume. Slowly increase the amplifier's input level until you hear slight distortion, then back it off slightly. This ensures the amplifier receives an optimal signal without clipping.
5.3 Issettjar tal-Crossover
Il- amplifier features Variable High Low Pass Crossover Controls. These allow you to filter specific frequencies to your speakers or subwoofers.
- Filtru Pass Għoli (HPF): Used for full-range speakers to prevent low frequencies from reaching them, improving clarity.
- Filtru tal-Pass Baxx (LPF): Used for subwoofers to allow only low frequencies to pass, enhancing bass response.
Adjust these controls to match the frequency response characteristics of your speakers and subwoofers.
5.4 Bass Boost Circuit
The built-in Bass Boost Circuit allows for an increase in bass output at specific frequencies. Use this feature sparingly and adjust to your preference, avoiding excessive boosting that could lead to distortion or speaker damage.
5.5 Bridged Mode Operation
Il- amplifier can be bridged at 4 Ohms to combine the power of both channels into a single, higher-power output, typically for driving a subwoofer. Refer to the wiring diagram for specific instructions on bridging the ampaktar ħaj.
6. Manutenzjoni
The Lanzar VIBE211 amplifier requires minimal maintenance. Periodically inspect the wiring connections for tightness and corrosion. Keep the amplifier's heatsink clean and free of dust or debris to ensure proper cooling. Use a soft, dry cloth for cleaning the exterior.
7 Issolvi l-problemi
Jekk tesperjenza problemi ma tiegħek amplifer, ikkonsulta t-tabella li ġejja qabel ma tfittex servizz professjonali:
| Problema | Kawża Possibbli | Soluzzjoni |
|---|---|---|
| Ebda Qawwa / Ebda Ħoss | Blown fuse; Loose power/ground/remote wire; Faulty head unit. | Check and replace fuse; Verify all power, ground, and remote connections; Test head unit functionality. |
| Ħoss Mgħawġ | Input level too high; Speaker impedance too low; Damaged speakers. | Adjust input level; Verify speaker impedance (2 Ohm stereo stable, 4 Ohm bridged); Inspect speakers for damage. |
| Amplifier Goes into Protection Mode | Overheating; Short circuit in speaker wiring; Low voltage. | Ensure adequate ventilation; Check speaker wires for shorts; Verify battery voltage u sistema ta' ċċarġjar. |
| L-ebda Bass mis-Subwoofer | LPF not enabled or set too high; Phase issue; Remote bass control set to minimum. | Adjust LPF setting; Check subwoofer phase; Increase remote bass control level. |
8. Speċifikazzjonijiet
Technical specifications for the Lanzar VIBE211 ampaktar ħaj:
- Power Output (RMS @ 4 Ohms): 2 x 90 Watts
- Power Output (Max @ 4 Ohms): 2 x 180 Watts
- Power Output (Max Bridged @ 4 Ohms): 1 x 360 Watts
- Power Output (RMS @ 2 Ohms): 2 x 150 Watts
- Ampitwal Tip: 2 Channel Mosfet
- Rispons ta' Frekwenza: 15 Hz - 35 kHz
- Proporzjon tas-sinjal għall-istorbju (S/N): 90 dB
- Fjus Rating: 15A
- Dimensjonijiet (W x H x L): 10.25 pulzieri x 2 pulzieri x 8 pulzieri
- Kontrolli tal-Livell tal-Input: Varjabbli
- Kontrolli Crossover: Variable High/Low Pass
- Stabbiltà: 2 Ohm Stereo Stable, Bridgeable at 4 Ohms
- Ċirkwiti ta' Protezzjoni: Advanced Power Protection LED Indicators
- Karatteristiċi Addizzjonali: Remote Subwoofer Bass Control, Electronic Crossover Network, Bass Boost Circuit, Soft Turn On/Off
9. Garanzija u Appoġġ
9.1 Informazzjoni dwar Garanzija
The Lanzar VIBE211 amplifier jiġi ma 'a 1-SENA limited warranty from the date of purchase. This warranty covers defects in materials and workmanship under normal use. Please retain your proof of purchase for warranty claims. The warranty does not cover damage caused by improper installation, accident, misuse, abuse, negligence, or unauthorized modification.
9.2 Appoġġ għall-Klijent
For technical assistance, troubleshooting beyond this manual, or warranty service, please contact Lanzar customer support. Refer to the official Lanzar webis-sit jew l-imballaġġ tal-prodott għal informazzjoni ta' kuntatt attwali.
