D149H181 Ed.08
AKO-D14918
Il- AKO-D14918 programming key allows you to quickly and easily copy configured settings from one controller to another with the same functionality
Twissijiet
-Using the equipment without following the manufacturer’s instructions may affect the device’s safety requirements.
-The unit must be used in a location protected from vibrations, water and corrosive gases, where the ambient temperature does not exceed that shown in the technical data.
-Connecting this key to unsupported devices (see table) can cause serious damage to both pieces of equipment.
-In equipment with active communication, log out of communications software or disconnect the cable before connecting the programming key. The communication controller’s address must be 1.
Deskrizzjoni
- LED COM
- REKORD EWLENIN
- EXTERNAL POWER CONNECTOR
- READ KEY
- LED ON
- CONNECTOR CABLE
Kompatibilità
Refer to the instruction manual of your equipment on its compatibility with the AKO-D14918 programming key.
Connecting incompatible devices can permanently damage the key.
Wiring
- IMPORTANTI: Pay attention to the orientation of the connector.
- AKO-80018
(Mhux obbligatorju) - AKO-D14918
Provvista ta' enerġija
-If the controller is in operation (on-site programming), the key does not require an external power supply (it is powered via the connecting cable).
-If the controller is NOT powered (workshop programming), the key requires a 12Vdc/500 mA external power supply (AKO-80018 jew ekwivalenti).
Operazzjoni
IMPORTANTI: After connecting the key to the equipment wait for 5 seconds before starting the reading or writing process.
RECORD key
Write the data contained in the key memory to the controller.
Keep the key pressed until the COM led starts flashing quickly.
When recording is complete the controller will reset.
READ key
It reads the data from the controller and stores them in the programming key.
Keep the key pressed until the COM led starts flashing quickly.
When recording is complete the controller will reset.
LED ON
Steady or flashing: Indicates that the key is connected to the controller.
LED COM
Sod: Indicates an error in the transmission/reception of data
Teptip mgħaġġel: Indicates transmission/reception of data in progress. At the end of the transmission LED COM se jintefa.
Teptip bil-mod: Indicates compatibility error- the data contained in the memory of the key is not compatible with the model of controller connected. Data can only be read from the controller to the key.
NOTA: To restart after a transmission or compatibility error, turn off the power supply or disconnect the controller connector cable.
IMPORTANTI: Qatt disconnect the programming key during data transmission.
Speċifikazzjonijiet tekniċi
Length of cable from programming key to controller . . . . . . . . . . . . . 300 mm
Provvista voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Vdc nominal
Supply current . . . . . . . . . . . . . . . . . . . . . . . . . . . . AKO-80018 / 500 mA máx.
Speċifikazzjonijiet ambjentali:
Ambient working temperature. . . . . . . . . . . . . . . . . . . . . . . . . . . . 0ºC to 50ºC
Storage temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -30ºC to 70ºC
AKO ELECTROMECÁNICA, SA
Av. Roquetes, 30-38 | 08812 Sant Pere de Ribes | Barċellona | Spanja
35D149181 REV.07 2025
Aħna nirriżervaw id-dritt li nipprovdu materjali li jistgħu jvarjaw xi ftit għal dawk deskritti fl-Iskedi Tekniċi tagħna.
Informazzjoni aġġornata hija disponibbli fuq tagħna websit.
Dokumenti / Riżorsi
 |
AKO D14918 Programming Key [pdfManwal tal-Istruzzjonijiet AKO-D14918, AKO-80018, D14918 Programming Key, Programming Key, Key |