Manwal tal-Utent tal-Kontrollur tal-Iċċarġjar Solari EPEVER Tracer1210AN G3 MPPT

1. Introduzzjoni

The Tracer-AN G3 series controllers, including the Tracer1210AN G3, are advanced MPPT solar charge controllers designed to optimize solar energy utilization and prolong battery lifespan. These controllers feature adaptive 3-stage charging, high tracking efficiency, and comprehensive electronic protections, making them suitable for various applications such as RVs, residential systems, and outdoor monitoring.

2. Istruzzjonijiet Importanti dwar is-Sigurtà

Please keep this manual for future reference. This manual contains the safety, installation, and operation instructions for the Tracer-AN G3 series MPPT solar charge controller.

• Aqra l-istruzzjonijiet u t-twissijiet kollha bir-reqqa qabel l-installazzjoni.
• No user-serviceable components inside. Do not disassemble or attempt to repair the controller.
• Mount the controller indoors. Avoid exposure to components and do not allow water to enter.
• Install in a well-ventilated place. The controller's heat sink may become hot during operation.
• Huwa ssuġġerit li jiġu installati fjusis/breakers esterni xierqa li jaħdmu malajr.
• Disconnect PV array connections and battery fuses/breakers before installation and adjustment.
• Il-konnessjonijiet tal-enerġija għandhom jibqgħu stretti biex jiġi evitat tisħin eċċessiv minn konnessjoni maħlula.

3. Ċaħdiet

Il-garanzija ma tapplikax għall-kundizzjonijiet li ġejjin:

• Damage caused by improper use or inappropriate environment (e.g., humid, high salt spray, corrosion, greasy, flammable, explosive, dust accumulative, or other severe environments).
• Actual current/voltage/power taqbeż il-valur tal-limitu tal-kontrollur.
• Ħsara kkawżata minn temperatura tax-xogħol li taqbeż il-firxa ratata.
• Arc, fire, explosion, and other accidents caused by failure to follow controller stickers or manual instructions.
• Żarmar mhux awtorizzat jew attentat ta' tiswija.
• Ħsara kkawżata minn force majeure.
• Ħsara seħħet waqt it-trasport jew l-immaniġġjar.

4. Karatteristiċi

• High quality and low failure rate components (ST or IR) to ensure service life.
• Teknoloġija MPPT avvanzata, b'Max. effiċjenza tat-traċċar ogħla minn 99.5%.
• Advanced MPPT control algorithm to minimize lost rate and time.
• Accurate recognizing and tracking technology of multi-peaks maximum power point.
• MPP usa' (punt tal-qawwa massima) li jaħdem voltage biex tottimizza l-utilizzazzjoni tal-PV.
• Maximum DC/DC conversion efficiency of 98%.
• Support multi-battery types including lithium batteries.
• Mgħammar b'funzjoni ta 'awto-attivazzjoni stabbli għal batteriji tal-litju.
• Issettja l-batterija voltage parametri fuq l-LCD.
• Kumpens tat-temperatura tal-batterija.
• Limit charging power & charging current to no higher than the rated value.
• Funzjoni tal-istatistika tal-enerġija f'ħin reali.
• Charging power reduction automatically for over-temperature.
• RS485 communication interface with optional 4G or Wi-Fi modules for remote monitoring.
• Standard Modbus communication protocol based on the RS485 communication bus.
• A power protection chip provides 5VDC/200mA power with over-current and short-circuit protections for the communication interface.
• Setting parameters via PC software, APP, or remote meter.
• Vol kostantitage output function.
• Protezzjonijiet elettroniċi komprensivi.
• Modi ta 'xogħol ta' tagħbija multipli.
• Low self-consumption, lower than 10mA.
• Operation at full load without charging power reduced in the working temperature range.

5. Karatteristiċi tal-prodott

5.1 Kontrollur Overview

The diagram below illustrates the main components and interfaces of the EPEVER Tracer series MPPT Solar Charge Controller.

The pins of the RS485 port are defined as follows:

5.2 Regoli dwar l-Ismijiet

The model name Tracer1210AN G3 follows a specific naming convention:

• G3: The 3rd generation product.
• AN: Common negative system.
• Vol massimu f'ċirkwit miftuħ PVtage: Value*10V (e.g., 10 indicates 100V).
• Batterija ratata voltage: 2 indicates 12/24VDC.
• Rated charging & discharging current: 1 indicates 10A; 2 indicates 20A; 3 indicates 30A; 4 indicates 40A.
• Serje ta' prodotti: Tracer.

6. Istruzzjonijiet ta 'installazzjoni

6.1 Prekawzjonijiet ta 'Installazzjoni

• Familiarize yourself with the installation steps before proceeding.
• Tinstallax il-kontrollur f'ambjenti umdi, ta 'melħ għoli, korrużjoni, żejtni, fjammabbli, splussivi, akkumulattivi ta' trab, jew ambjenti severi oħra.
• Be careful when installing batteries. Wear eye protection when installing open-type lead-acid batteries and rinse with clean water immediately if battery acid contacts skin.
• Keep batteries away from metal objects to prevent short circuits.
• Ensure the surrounding environment is well ventilated, as acid gas may be generated when batteries are charged.
• Avoid direct sunlight and rain infiltration when installing outdoors.
• Ensure tight power connections and secure cables with clamps to prevent high heat from loose connections.
• Only charge lead-acid and lithium-ion batteries within the control range of this controller.
• The battery connector can be wired to a single battery or a bank of batteries.
• Select system cables according to 5A/mm² or less current density.
• The grounding wire size should not be less than 4mm².
• The torque for tightening wiring screws should not be less than 1.2 N·m.

6.2 Requirements for the PV Array

The controller needs to suit various types of PV modules. The serial connection of PV modules suitable for different controllers can be calculated based on the open-circuit voltage (Voc) u l-punt tal-qawwa massima voltage (VMPP) of the MPPT controller. Refer to the technical specifications for detailed values.

6.3 Daqs tal-Wajer

Il-wajers u l-metodi ta 'installazzjoni għandhom jikkonformaw mar-rekwiżiti tal-kodiċi elettriku nazzjonali u lokali.

Daqs tal-Wajer PV

The PV array's output current varies with size, connection method, and sunlight angle. The minimum wire size can be calculated using the ISC (short circuit current) from the PV module's specifications. The PV array's ISC must not exceed the controller's maximum PV input current.

Daqs tal-Wajer tal-Batterija u tat-Tagħbija

The battery and load wire size should conform to the rated current.

6.4 Immuntar

Il-kontrollur jeħtieġ mill-inqas 150mm ta 'spazju 'l fuq u taħt għal fluss ta' arja xieraq. Il-ventilazzjoni hija rakkomandata ħafna jekk tkun immuntata f'kompartiment.

Step 1: Determine the installation location and heat-dissipation space.

6.5 Dijagramma tal-Wiring

Step 2: Connect the system in the order of ①battery > ②load > ③PV array by the following schematic wiring diagram, and disconnect the system in the reverse order.

No-Battery Mode

Battery Mode (with BMS-Link)

6.6 L-ert

Tracer-AN G3 series are common-negative controllers. Negative terminals of the PV array, the battery, and the load can be grounded simultaneously, or any negative terminal can be grounded. However, the grounding terminal on its shell must be grounded to shield electromagnetic interference and avoid electric shock.

6.7 Qabbad Aċċessorji

Step 4: Connect the temperature sensor.

Table 6.3: Temperature Sensor Models

	Deskrizzjoni	Mudell	Immaġni
Aċċessorju Inkluż	Qabbad is-sensor tat-temperatura	RT-MF58R47K3.81A
Aċċessorju Fakultattiv	Sensor tat-temperatura remot	RTS300R47K3.81A

Connect the accessories for RS485 communication. Refer to Section 7.4 for details.

6.8 Power On the Controller

Pass 5: Connect the battery fast-acting fuse to power the controller. Check the battery indicator status (the controller operates normally when the indicator is lit green). Connect the fast-acting fuse and circuit breaker of the load and PV array. The system will then operate in preprogrammed mode.

7. Operazzjoni

7.1 Display LCD

The LCD screen provides real-time information about the system status. The display screen can be viewed clearly when the angle between the end-user's horizontal sight and the display screen is within 90°. If the angle exceeds 90°, the information cannot be viewed b'mod ċar.

7.2 Buttuni

7.3 Interface Status Description

Kodiċi ta' Żball

When the load current reaches 1.02-1.05 times, 1.05-1.25 times, 1.25-1.35 times, and 1.35-1.5 times more than the rated value, the controller will automatically turn off the loads in 50s, 30s, 10s, and 2s respectively.

Browse Interface

Press the SELECT button to cycle through the following interfaces:

7.4 Settings

Primary and Secondary Modes

The Primary mode is used for BMS communication, while the Secondary mode is used for RS485 communication, allowing remote setting of battery parameters via PC software or APP. To switch modes:

1. Press the SELECT button to switch to the first TYPE interface.
2. Press the ENTER button; the value will flash.
3. Press the SELECT button to switch the mode ('nn' for primary, 'S' for secondary).
4. Agħfas il-buttuna ENTER biex tikkonferma l-għażla.

BMS Protocol Number

When using lithium batteries with BMS, the BMS-Link module converts BMS protocols to standard protocols. To set the BMS protocol number:

1. In Primary mode (first TYPE interface displays 'nn'), press the SELECT button to switch to the second TYPE interface.
2. Press the ENTER button to switch to the BMS protocol number (default 01, scope: 0-231).
3. Press the SELECT button to confirm selection.

Clear Generated Energy

1. Press and hold the ENTER button for 5s under the PV-generated energy interface; the value will flash.
2. Agħfas il-buttuna ENTER biex tneħħi l-enerġija ġġenerata.

Switch Battery Temperature Unit

Press and hold the button for 5s under the battery temperature interface to switch the temperature unit.

Tip ta 'batterija

The controller supports various battery types. The default is Sealed. Lithium battery types include LiFePO4 and Li(NiCoMn)O2. A 'User' option allows custom settings.

Local Setting of Battery Type:

1. Agħfas il-buttuna SELECT biex taqbeż għall-volum tal-batterijatage interface.
2. Agħfas u żomm il-buttuna ENTER sakemm l-interface tat-tip tal-batterija jteptep.
3. Press the SELECT button to change the battery type (e.g., Sealed, Gel, FLD, Lithium types, User).
4. Agħfas il-buttuna ENTER biex tikkonferma.

Remote Setting of Battery Parameters:

Before remote setting, the communication mode should be set to Secondary mode.

• Via PC Software: Connect the controller's RJ45 port to the PC's USB interface via a USB to RS485 cable. When selecting 'USE' battery type, set voltage parameters via PC software.

• Via External WiFi 2.4G or Bluetooth Adapter: Connect the controller to an external WiFi 2.4G or Bluetooth adapter via the RS485 communication port. End-users can set voltage parameters via the APP after selecting 'USE' battery type. Refer to the cloud APP manual for details.

• Via MT52 Remote Meter: Connect the controller to the remote meter (MT52) through a standard network cable. After selecting 'USE' battery type, set voltage parameters via the MT52. Refer to the MT52 manual for details.

7.5 Iċċarġjar tal-batterija Stages

The controller employs a three-stage battery charging algorithm: Bulk Charging, Constant Charging (Equalize and Boost), and Float Charging. This method extends battery lifespan.

1. Iċċarġjar Bulk: Il-batterija voltage għadu ma laħaqx vol kostantitage. The controller operates in constant current mode, delivering maximum current (MPPT Charging).
2. Iċċarġjar kostanti: Ladarba l-batterija voltage jilħaq il-volum kostantitage set point, the controller switches to constant charging mode. MPPT charging stops, and the charging current gradually drops. This stage includes Equalize Charging (on the 28th of each month) and Boost Charging (default 2 hours).
3. Iċċarġjar tal-Galleġġjant: After constant charging, the controller reduces battery voltage għall-float iċċarġjar issettjat minn qabel voltage by reducing current. The battery is weakly charged to maintain a fully charged state. If load power exceeds solar array power, the controller will no longer maintain float charging. The system exits float charging and re-enters bulk charging if battery voltage drops below the boost voltagerġa 'qabbad il-voltage.

7.6 Load Modes

The controller offers multiple load work modes. When the LCD shows the load type interface, operate as follows:

1. Agħfas il-buttuna AGĦŻEL biex taqbeż għall-interface tat-tip tat-tagħbija.
2. Agħfas u żomm il-buttuna ENTER sakemm l-interface tat-tip tat-tagħbija titfi.
3. Agħfas il-buttuna SELECT biex timmodifika t-tip tat-tagħbija.
4. Agħfas il-buttuna ENTER biex tikkonferma.

8. Protezzjonijiet

When the controller's internal temperature reaches 81°C, the charging power automatic reduction function is enabled. Temperature increases by 1°C, and the charging power is reduced by 5%, 10%, 20%, and 40%. If the internal temperature exceeds 85°C, the controller stops charging the battery. When the internal temperature is lower than or equal to 75°C, the controller resumes charging per the rated charging power.

9 Issolvi l-problemi

10. Manutenzjoni

The following inspections and maintenance tasks are recommended at least twice yearly for good performance:

• Ensure no blockage on airflow around the controller. Clear any dirt and fragments on the radiator.
• Check all naked wires to ensure insulation is not damaged by sun exposure, frictional wear, dryness, insects or rats, etc. Repair or replace wires if necessary.
• Verify the indicator display is consistent with actual operation. Pay attention to any troubleshooting or error conditions and take corrective action.
• Confirm that terminals have no corrosion, insulation damage, high temperature, burnt/discolored signs, and tighten terminal screws to the suggested torque.
• Clear dirt, nesting insects, and corrosion in time.
• Check and confirm that the lightning arrester is in good condition. Replace if necessary to avoid damaging the controller and other equipment.

11. Speċifikazzjonijiet Tekniċi

Parametri elettriċi

Parametri Ambjentali

Parametri Mekkaniċi

12. Għajnuniet għall-Utenti

• Wiring Sequence is Crucial: Always connect the battery first, then the PV array, and finally the load. Disconnect in reverse order. This prevents damage to the controller.
• Monitor Battery Voltage: Kun żgur li l-batterija tiegħek voltage is at least 8V for the controller to activate. If it's below this, you may need to charge it externally first.
• Utilize Communication Modules: For advanced monitoring and parameter adjustments, consider using the optional WiFi or Bluetooth modules with the EPEVER APP, or connect to a PC with the appropriate cable and software.
• Ventilazzjoni xierqa: Adequate airflow around the controller is essential to prevent overheating, especially during high power operation. Ensure the 150mm clearance is maintained.
• Custom Battery Settings: If using a 'User' defined battery type, carefully review and set all voltage parameters according to your battery manufacturer's specifications to optimize performance and lifespan.
• Manutenzjoni regolari: Perform the recommended bi-annual maintenance checks to ensure all connections are tight, clean, and free from damage, which will prolong the life of your system.

13. Garanzija u Appoġġ

For detailed warranty information, please refer to the official EPEVER warranty policy. For technical support or inquiries, you can contact EPEVER directly:

• HUIZHOU EPEVER TEKNOLOĠIJA, LTD.
• Telefon: +86-752-3889706
• Email: info@epever.com
• Websit: www.epever.com

Manwal komprensiv għall-utent f'format PDF huwa wkoll disponibbli biex jitniżżel: EPEVER Tracer-AN G3 Series User Manual (PDF)