Introduzzjoni
This manual provides comprehensive instructions for the safe and efficient operation, installation, maintenance, and troubleshooting of your HUMILABS OL12-BD031A Dehumidifier. Please read this manual thoroughly before using the appliance and keep it for future reference. For a downloadable PDF version of this manual, please refer to the official product page or contact customer support.
Istruzzjonijiet tas-Sigurtà
Read all instructions carefully before commissioning. Failure to comply with the safety information and instructions may result in electric shock, fire, and/or serious injury. Keep these instructions and all safety notes for future reference.
Twissijiet Ġenerali
- Attenzjoni! Do not open the unit until the mains plug has been removed from the mains socket. Danger to life due to electric shock! Have repairs carried out only by an authorised specialist workshop.
- Only install the unit in rooms with an area of more than 6m².
- Do not install the appliance in a place where flammable gas may escape.
- The dehumidifier is used to remove excess moisture from the air. The refrigerant used is the environmentally friendly R290 (propane). Due to its high flammability, special precautions must be taken.
Simboli Spjegati
- ⚠ Danger due to flammable gas: This symbol alerts you to dangers to health and life from extremely flammable gas. If refrigerant escapes and comes into contact with a fire or a heating element, harmful gases are produced and there is a risk of fire.
- ⓘ Observe operating instructions: This symbol indicates that you should read the operating instructions before installing and operating the appliance.
- ⓘ Observe operating instructions and operating notes: This symbol draws your attention to the need to observe and comply with the operating instructions and the operating instructions contained therein.
- ⚠ Observe repair instructions, technical manual: Activities on the refrigeration circuit, such as disposal, repairs and maintenance activities, may only be carried out by persons with a relevant certificate of competence and only in accordance with the manufacturer's instructions.
- ⚠ Danger: There is danger to the unit or objects in the vicinity of the unit.
- ⚡ Electrical hazard: Periklu ta 'xokk elettriku.
Istruzzjonijiet Speċifiċi dwar is-Sigurtà
- Tużax xi aġenti għajr dawk rakkomandati mill-manifattur biex tħaffef il-proċess tad-defrosting jew biex tnaddaf id-dehumidifier.
- The appliance must be stored in a room without continuously operating ignition sources (e.g. open flames, a gas appliance switched on or an electric heater switched on).
- Do not disassemble, pierce or burn the appliance, even after use.
- Use the on/off switch to turn the unit on and off. Never use the plug to switch the unit on and off.
- The appliance may only be installed, operated and stored in a room with a floor area of more than 6m².
- Maintenance must only be carried out in accordance with the manufacturer's instructions. The unit must be disconnected from the power supply during maintenance.
- L-unità għandha tinħażen f'żona b'ventilazzjoni tajba fejn id-daqs tal-kamra jikkorrispondi għad-daqs tal-kamra speċifikat għat-tħaddim.
- All work processes that affect safety-relevant aspects (e.g. repairs) may only be carried out by qualified personnel.
- Do not immerse the unit in water or other liquids and do not expose it to rain, moisture or other liquids.
- If the mains cable is damaged, it must be replaced by the manufacturer, its service partner or similarly qualified persons in order to avoid a hazard.
- Please contact a professional to have the product repaired. Improper repairs may result in injury to the user.
- Disconnect the appliance from the power supply before moving, cleaning or servicing it and also when it is not in use or in case of malfunctions. Never pull on the power cord.
- Observe the national installation regulations and only connect the unit to a properly installed protective contact socket with a mains voltage/frequency/power according to the type plate.
- Do not place any objects on the dehumidifier. Do not climb or sit on the unit.
- Do not unplug the unit by pulling the mains cable. Always grasp the mains plug for this purpose.
- Do not tilt or overturn the unit. This may cause water leakage and damage the appliance.
- This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision and/or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children must not play with the appliance. Cleaning and maintenance must not be carried out by children without supervision.
- Do not place the unit directly against a wall or under a wall cabinet or similar. The unit requires a free space of at least 30 cm at the top and on all sides.
- The unit is to be used only in the temperature range between 5°C and 35°C. Do not use the unit in a wet area. The unit is not splash-proof.
- Position the unit on a flat, stable, non-slip, hard and dry surface. This is to avoid increased noise, vibration, water leakage or electric shock.
- Never insert your fingers or other objects into the unit. This can cause damage to the unit. Do not touch the air inlet or the aluminium fins of the unit.
- Unplug the unit after you have switched it off or do not intend to use it for a long period of time or when you want to clean it.
- The working area of the unit must be at least 6m². It must be ensured that there are no flammable materials in the working area of the unit.
- Do not clean the dehumidifier with water or chemicals. Prevent water from getting on/near the unit. Do not spray the unit with flammable liquids or cleaning agents.
- Do not touch the ventilation slots. Keep the air inlet and outlet clear of obstructions. Keep all necessary ventilation openings free of obstructions.
- Do not use the appliance if the mains lead is damaged. Do not use the unit in hermetically sealed rooms.
- Keep the water tank free of foreign objects. Place the unit away from heaters or heat-generating appliances.
- The unit must not be used in environments with a high dust or chlorine content.
- Only use the appliance if your socket outlet is equipped with an RCD (ground fault circuit interrupter).
- Do not operate/touch the unit with wet hands. Prevent water from splashing onto the appliance.
- Do not attempt to carry out repairs or other adjustments to the unit yourself.
- Ensure that the dehumidifier is positioned away from fire, flammable, corrosive and explosive materials.
- Insert the mains plug firmly and securely into the socket. Do not operate the dehumidifier via a multiple socket, plug adapter or extension cord.
- Do not operate the unit if it has been dropped, damaged or shows signs of malfunction.
- Do not operate the unit in the immediate vicinity of walls, curtains or other objects that may block the air inlet and outlet.
- If the unit has been tilted more than 45°, let it stand upright for at least 24 hours before using it.
- Tħaddimx jew taħżinx l-unità fid-dawl tax-xemx dirett jew fix-xita.
- Never place the mains cable or the appliance on hot surfaces or near sources of heat. Lay the mains cable so that it does not come into contact with hot or sharp-edged objects.
- Do not bend the mains cable or wrap it around the unit as this may cause the cable to break.
- Please note that in addition to switching off the unit, you must also pull the mains plug out of the protective contact socket to completely disconnect the unit from the mains.
- No naked flames, cigarettes or other possible sources of ignition shall be used inside or near the equipment.
Noti dwar ir-refriġerant R290
- The unit is only designed for use with R-290 (propane) gas as refrigerant.
- The refrigerant circuit is sealed. Maintenance work in this regard may only be carried out by a qualified technician. The maintenance manual must be requested by the technician from the manufacturer.
- Tneħħix ir-refriġerant fl-atmosfera.
- R290 (propane) is extremely flammable and heavier than air. It first accumulates in low areas, but can be circulated by fans.
- If propane gas is present, or the presence is suspected, do not allow untrained persons to search for the cause.
- The propane gas used in this appliance is odourless. Therefore, gas may have leaked even without a noticeable odour.
- The components used are designed for propane gas and are therefore not ignitable and spark-free. Components may only be replaced by identical spare parts approved by the manufacturer.
- Għandha tiġi osservata konformità mar-regolamenti nazzjonali tal-gass.
Prodott Overview
The HUMILABS OL12-BD031A is a powerful dehumidifier designed to reduce moisture and prevent mold in various indoor environments. It features multiple operating modes, a 24-hour timer, and convenient mobility options.
Deskrizzjoni tal-Apparat



Komponenti Ewlenin
Refer to the PDF manual for detailed diagrams of the device components (Figures 1 & 2 on OCR Page 8).
- Panel tal-Kontroll: Located on the top, for operating the unit.
- Wiri tal-Umdità: 3-coloured indicator for humidity levels.
- Panel ta' quddiem: Main front casing.
- Roti tar-riġnu: 4 wheels for easy movement.
- Side Part: Side casing tal-unità.
- Bord ta 'wara: Ċ ta' waraasing.
- Manku tal-Ġarr: Għall-portabbiltà.
- Air Outlet (left): Where dehumidified air is expelled.
- Dħul ta' l-Arja: Where ambient air is drawn in.
- Tank tal-Ilma: 2L capacity for collected water.
- Żbokk tad-Drenaġġ: Għal għażla ta' drenaġġ kontinwu.
- Kejbil tal-Mejns: Kejbil tal-provvista tal-enerġija.
Setup
Istruzzjonijiet għall-installazzjoni
- Only operate the appliance in rooms with at least 6m² floor space.
- Remove all adhesive tapes that were used to secure the unit for transport.
- Keep doors and windows closed to save more energy. Check that the appliance is standing securely on firm, level and dry ground.
- Qatt tinstalla l-unità fejn tista' tkun esposta għall-kundizzjonijiet li ġejjin:
- Heat sources such as radiators, heat registers, stoves or other products that generate heat.
- F'żona fejn iż-żejt jew l-ilma jistgħu jiġu mferrxa.
- Dawl tax-xemx dirett.
- Mechanical vibrations or shocks.
- Excessive dust exposure.
- Lack of ventilation, e.g. in the cupboard or bookshelf.
- Wiċċ irregolari.
- Make sure that the socket outlet is equipped with an RCD circuit breaker (ground fault circuit interrupter). If you are not sure whether this is the case, you can ask your electrician or use a personal protection plug (available in DIY stores).
- To save power and avoid potential hazards, unplug the unit when not in use.
- Keep at least 30cm distance around the unit from walls and objects. Make sure that the air outlet is clear and that there are no curtains or textiles above it.
Refer to the PDF manual for a diagram illustrating the recommended 30cm clearance around the dehumidifier (OCR Page 10).
Qabel il-Kummissjonar
After unpacking the unit, check it for completeness and possible transport damage to avoid hazards. If in doubt, do not use it, but contact our customer service. Please read the operating instructions carefully before using your dehumidifier for the first time.
- Carefully remove the unit from its sales packaging.
- Neħħi l-partijiet kollha tal-ippakkjar.
- Clean the unit and all accessories from packaging dust residues, according to the instructions in the "Maintenance" section.
- Leave the unit in the final position for at least 24 hours before commissioning. This allows the refrigerant to settle.
Operazzjoni
Kummissjonar
- Before plugging in the mains plug, check the unit and especially the cable for damage. The unit may only be operated with a faultless mains cable.
- Plug in the mains cable and switch on the unit with the on/off switch.
- ATTENZJONI: Always allow the unit to run for at least 35 minutes before switching it off and never switch the unit off and on continuously. There is a risk of compressor damage.
- After switching off the 12L dehumidifier, leave it to stand for at least 3 minutes without moving the appliance so that the water in the drip tray can drain off completely.
- The higher the humidity in a room and the higher the temperature in it, the better the 12L dehumidifier can dehumidify the air. Therefore, the compressor will generate heat and thus warm the room air. This is quite normal and need not worry you.
- Nota: Before using the unit for the first time, we recommend that you operate it with the window open for 5-10 minutes to remove any residues that may be present due to production. Any odour that may occur is normal and disappears after a short time. This is not a malfunction of the unit. Ensure that there is sufficient ventilation.
Panel tal-Kontroll u Display

Refer to the PDF manual for detailed diagrams of the control panel buttons and display indications (Figures 3 & 4 on OCR Page 24).
Swiċċ mixgħul / mitfi
- When you plug in the unit, a beep sounds and all indicators light up for 1 second, then only the "POWER" indicator lights up.
- Press the On / Off switch to turn the unit on; the dehumidifier starts in automatic mode with a target humidity of 60%RH and high air flow.
- Agħfas l-iswiċċ mixgħul/mitfi mill-ġdid biex titfi l-unità. Il-kompressur jintefa immedjatament u l-fann jintefa b'dewmien ta '30 sekonda.
Modi Operattivi
By pressing the Mode button repeatedly, you can choose between 3 operating modes:
- Laundry Drying / Continuous Operation: The dehumidifier dehumidifies with a high air flow rate until it is switched off or the water tank is full. In this mode, no target humidity can be set and the fan speed cannot be changed. When the unit is switched off, the setting is saved. When it is switched on again, the dehumidifier restarts in this setting.
- Modalità Awtomatika: If the humidity is ≥ +3% than the set value, the fan starts working and the compressor starts after 3 seconds. If the humidity is ≤ -3% than the set value, the compressor switches off and the fan switches off with a delay. Both the fan speed and the humidity can be set in automatic mode. When the unit is switched off, the setting is saved. When it is switched on again, the dehumidifier restarts in this setting.
- Modalità Sleep: If no further button touches are made within 10 seconds of selecting sleep mode, all displays gradually go dark and the fan speed is automatically switched from high to low. Touch any button to reactivate the display illumination. Press the "Mode" key again to exit sleep mode. In sleep mode, the fan speed cannot be changed and error codes are not displayed. Setting a target humidity is possible in sleep mode.


L-issettjar ta' l-umdità
- The unit is equipped with a modern hygrostat (humidity controller) and switches off automatically after reaching the desired humidity in order to save energy. The compressor switches off first and then the fan 30 seconds later. When the humidity in the room rises again, the 12L dehumidifier switches on automatically.
- By repeatedly pressing the button, the target humidity can be set between 30% and 80% in 5% steps.
- The set target humidity is now shown on the display for approx. 5 seconds.
- To have the current room temperature shown on the display, press and hold this button until the room temperature is shown. After approx. 5 seconds, the display shows the current room humidity again.
- Id-dehumidifier jibda jiddewmidifika meta l-umdità tal-kamra tkun mill-inqas 3% ogħla mill-umdità fil-mira stabbilita.
Timer
- Press the timer button to start the timer function. By pressing repeatedly, you can set a time of 1-24 hours in 1 hour steps. If the timer is activated, this is indicated by the corresponding symbol on the display.
- Jekk tattiva t-tajmer waqt it-tħaddim, l-apparat jintefa wara l-ħin stabbilit.
- Jekk tattiva t-tajmer waqt li l-unità tkun fil-modalità standby, l-unità tibda awtomatikament wara li jkun għadda l-ħin stabbilit.
- To switch off the timer, press the button repeatedly until "00" is displayed.
Veloċità
- Agħfas din il-buttuna biex taqleb bejn iż-żewġ veloċitajiet tal-fann.
- The currently selected fan speed is shown on the display.
Lock tas-Sigurtà tat-Tfal
- Press and hold this button to activate the child lock. No more settings can be made. If the child lock is active, this is indicated by the corresponding symbol on the display. Press and hold this button again to deactivate the child lock. When the unit is restarted after a power failure or similar, the child lock is always deactivated.

3-Colour Humidity Display
- Blu: Umdità <45%
- Aħdar: Humidity 45%≤RH≤65%
- Aħmar: Umdità > 65%
- If an error or status message appears on the display, the humidity indicator lights up red.
Manutenzjoni
Regular maintenance ensures the longevity and efficient operation of your dehumidifier. Always switch off the unit and disconnect it from the mains before performing any maintenance.
Battal it-Tank tal-Ilma
- When the water tank is full, the 12L dehumidifier switches off automatically and the tank "full" indicator on the display lights up. This is also signalled acoustically.
- You must empty the water tank to be able to put the dehumidifier back into operation. To do this, always switch off the unit first and disconnect the mains plug.
- Grasp the water tank by the two recesses on the side and carefully pull it backwards out of the appliance.
- Attenzjoni: To avoid spilling water, it is recommended to hold the water tank with both hands when removing and transporting it.
- Empty the water tank completely into a wash basin or similar. If necessary, clean the inside and outside of the tank.
- Carefully reinsert the tank after it has been completely emptied. To do this, grasp the water tank on both sides and push it straight into the appliance. Make sure that the tank is correctly inserted to ensure proper operation of the appliance.
- Attenzjoni: To ensure correct and safe operation of the appliance, the float and its locking device must not be removed from the water tank. Otherwise, this may cause the water tank to overflow.
- If the water tank is dirty, it should be cleaned. Use cold or warm water without additives. Additives or cleaning utensils such as washing-up liquid, steel wool, benzene or other chemical cleaners are not suitable as they can damage the tank and cause leakage.

Refer to the PDF manual for diagrams on water tank removal and reinsertion (OCR Page 13).
Hose Drainage (Continuous Drainage)
The 12L dehumidifier can also be operated using a drainage hose (Ø9.0mm). To do this, remove the water tank and attach a drainage hose. Proceed as follows:
- Neħħi t-tank tal-ilma.
- Attach the drainage hose to the drain of the drip tray.
- Put the water tank back in place and guide the hose through the recess of the drainage outlet.
Refer to the PDF manual for diagrams on hose attachment (OCR Page 14).
Attenzjoni:
- Make sure that the hose does not run higher than the hose connection on the appliance at any point so that the water can drain off undisturbed.
- Kun żgur li l-pajp tad-drenaġġ ma jkunx kinked jew imblukkat. Iċċekkja dan regolarment.
- Make sure that the end of the hose is not below the water surface of the drain or similar.
The appliance must be switched off and disconnected from the mains after each use and before attaching or removing accessories by pulling the mains plug out of the protective contact socket after switching off. Let the appliance cool down to room temperature before cleaning and/or storing it.
Defrost Awtomatiku
The dehumidifier is equipped with a temperature-dependent defrost function. At a room temperature between 5°C and 16°C, the unit starts defrosting every 45 minutes. During the defrosting process, the power LED flashes.
Intervalli ta' Manutenzjoni
| Maintenance and Maintenance Interval | Before each commissioning | At Demand | Mill-inqas il-ġimagħtejn kollha | Mill-inqas il-ġimagħtejn kollha | Mill-inqas is-6 xhur kollha | Mill-inqas kull sena |
|---|---|---|---|---|---|---|
| Check air inlet and air outlet and remove impurities. | X | X | ||||
| Tindif ta' barra | X | X | ||||
| Visual inspection of the water outlet (hose connection) for contamination | X | X | ||||
| Check the air filter for dirt and foreign bodies, clean or replace if necessary. | X | X | ||||
| Check the unit for damage (mains cable, housing, tank, fan wheel). | X | |||||
| Test run | X | X | ||||
| Tbattal it-tank jew iċċekkja d-drenaġġ tal-pajp | X | |||||
| Spezzjoni viżwali tas-sokits użati. | X | |||||
| Testing the residual current device (RCD). | X |
Check Air Inlet and Air Outlet
The unit draws in air from the rear and blows it out again from the side. Make sure that the air inlet and air outlet are not blocked and check this each time you use the unit. Make sure that no objects or walls obstruct the air inlet or air outlet and observe the distance rules.
Iċċekkja l-Filtru tal-Ajru
This should be done every 2 weeks. To do this, switch off the machine, disconnect the mains cable and remove the water tank. You can now pull the filter downwards out of the machine.

Rinse the filter with warm (maximum 40°C) clear water and let it dry. Make sure that the filter is not exposed to high temperatures and do not use any cleaning agents or other substances (such as petrol or alcohol). You can then reattach it to the unit.
Check the Drainage Hose
Check the hose used for hose drainage regularly for blockages and damage. If the hose is blocked or damaged, replace it with a new one.
Storage of the Dehumidifier
Jekk id-dehumidifier ma jintużax għal perjodu itwal ta' żmien:
- Itfi u aqla l-unità.
- Żvojta t-tank tal-ilma kompletament u kun żgur li ma jkunx hemm aktar ilma fl-appliance.
- Remove and clean the dust filters. Make sure that the filters are completely dry before reinserting them.
- It is recommended to clean the unit completely when storing it for a longer period of time.
- Store the dehumidifier in an upright position.
- Store the dehumidifier in a safe, cool, dry and well-ventilated place indoors. Keep the unit away from direct sunlight, too high/low temperatures and high dust exposure. Make sure that the unit does not come into contact with corrosive gases or similar.
ATTENZJONI! The evaporator inside the unit must be dried before the unit is packed. This is used to prevent damage to the components and mould. Pull out the plug from the mains socket and place the unit in a dry, open place for a few days to dry it.
Issolvi l-problemi
If you encounter issues with your dehumidifier, refer to the following common problems and solutions. If the problem persists, contact customer support.
Mistoqsijiet Frekwenti (FAQ)
L-unità mhux se tixgħel.
- Is the unit plugged in correctly?
- Is the water tank inserted correctly?
- Is the tank "full" indicator lit?
- Il-fjus nefaħ?
- It-temperatura tal-kamra hija 'l fuq minn 35°C jew inqas minn 5°C?
- Is the timer function or the child lock activated?
- If above is ok, then try again in 10 minutes.
Il-kapaċità tad-dehumidifikazzjoni hija baxxa wisq.
- Is the dust filter dirty?
- Id-daħla jew l-iżbokk tal-arja huma mblukkati?
- Is the temperature or humidity too low?
L-unità ma tintefax fil-mod awtomatiku.
- It-twieqi u l-bibien huma magħluqa?
- Does any appliance produce steam in this room?
- Il-kamra hija kbira wisq?
L-unità hija qawwija ħafna.
- Is the dust filter dirty?
- Is it standing on firm, level and suitable ground?
- Does the unit touch the wall of the room?
- For tiled floors, it is advisable to place a piece of carpet underneath.
Il-fjus ikompli jonfoħ.
- The RCD (ground fault circuit interrupter) keeps tripping. Stop operation and contact us.
The mains cable or the plug becomes disproportionately warm.
- Stop operating and contact us.
There are objects or water in the unit.
- Stop operating and contact us.
Error/Status Messages
Attenzjoni: Switch off and unplug the unit immediately and contact the customer service if anything unusual happens.
| Kodiċi ta' Żball | Kawża Possibbli | Possible Effect | Soluzzjoni |
|---|---|---|---|
| E2 | Żball tas-sensorju tal-umdità | The unit switches off for safety reasons. | Ikkuntattjana |
| LO | Humidity below 20%RH | The unit switches off for safety reasons. | Wait until the air humidity is above 20%RH. |
| HI | Humidity above 90%RH | The unit switches off for safety reasons. | Wait until the air humidity is below 90%RH. |
| CL | Temperatura tal-kamra taħt l-5°C | The unit switches off for safety reasons. | Wait until the room temperature is above 5°C. |
| CH | Temperatura tal-kamra 'l fuq minn 38°C | The unit switches off for safety reasons. | Wait until the room temperature is below 35°C. |
Speċifikazzjonijiet
| Karatteristika | Speċifikazzjoni |
|---|---|
| Isem tal-Prodott | OL12-BD031A |
| Numru tal-Mudell | OL12-BD031A |
| Voltage | AC220-240V/50 Hz (220 V) |
| Qawwa Rated | 200W |
| Current Consumption (30°C 80% humidity) | 1.2 A |
| Max. Suction/Pressure Side Operating Pressure | 0.7MPa / 3.2MPa |
| Kapaċità ta 'Deumidifikazzjoni | 12 L/Day (30°C 80% humidity) |
| Piż | 10.0 kg |
| Temperatura Operattiva Permissibbli | 5-35°C |
| Refrigerant / Amount | R290 / 50g |
| Kapaċità tat-Tank tal-Ilma | 2.0 L (1.1-2.5L) |
| Emissjoni ta' Storbju | ≤ 38 dB(A) |
| Dimensjonijiet (L x W x H) | 255x220x445 mm (250*220*445mm) |
| Air Flow Rate Fan Stage 1 | 100m³/h |
| Air Flow Rate Fan Stage 2 | 120m³/h |
| Ċertifikazzjoni | CE |
| Funzjoni | Bucket Full Indicator Light, External Drain Connect |
| Oriġini | Iċ-Ċina kontinentali |
Għajnuniet għall-Utent
- For optimal performance, ensure the dehumidifier is placed in a room with at least 6m² floor space and maintain 30cm clearance from walls and objects.
- Utilize the intelligent mode for daily use, continuous mode for very damp conditions, and sleep mode for quiet nighttime operation.
- Ħu bil-quddiemtage of the 24-hour timer to automate the unit's operation according to your schedule.
- Regularly clean the air filter (every 2 weeks) to maintain air purification quality and dehumidification efficiency.
- Use the 360-degree rotatable wheels and ergonomic handles for easy relocation of the unit between rooms.
- If using continuous drainage, ensure the hose is not kinked, blocked, or running uphill to prevent water backup.
- Activate the child safety lock to prevent accidental changes to settings, especially in households with children or pets.
- When storing the unit for extended periods, ensure the water tank is completely empty and the evaporator is dry to prevent mold and component damage.
Garanzija u Appoġġ
The HUMILABS OL12-BD031A Dehumidifier comes with a 12-month warranty. For any technical assistance, troubleshooting beyond this manual, or warranty claims, please refer to your purchase documentation for seller contact information or contact the manufacturer directly. Do not attempt to repair the unit yourself, as this may void the warranty and pose safety risks.
Rimi
The release of refrigerant (R290) into the atmosphere is strictly prohibited.
This product must not be disposed of in household waste. This dehumidifier must be taken to a recycling point for electronic and electrical equipment in accordance with local regulations. Contact your local authorities for information on designated collection points.