1. Prodott Aktarview
This manual provides instructions for the Magene H003 Heart Rate Sensor and the Magene S3+ Speed/Cadence Sensor. These devices are designed to track your cycling performance and heart rate, offering dual-mode ANT+ and Bluetooth connectivity for broad compatibility with various cycling computers, smartwatches, and fitness applications.
2. Kontenut tal-Pakkett
Magene H003 Heart Rate Sensor Package:
- 1x Heart Rate Sensor Unit
- 1x Batterija CR2032 (installata minn qabel fis-sensor)
- 1x Adjustable Elastic Chest Strap
- 1x Manwal għall-Utent
Magene S3+ Speed/Cadence Sensor Package:
- 1x Speed/Cadence Sensor Unit
- 2x Kuxxinetti tal-gomma
- 2x Rubber Bands
- 1x Manwal għall-Utent
3. Konfigurazzjoni u Installazzjoni
3.1 Magene H003 Heart Rate Sensor Setup
- Attivazzjoni tal-batterija: Open the battery compartment cover of the main unit. Remove the insulating strip from the CR2032 battery. Reinstall the battery and compartment cover.
- Assemblaġġ taċ-ċinga: Buckle the heart rate sensor unit to the heart rate monitor chest strap.
- Adjust Strap Length: Adjust the length of the chest strap (64-86cm) so that it can be worn comfortably on your chest.
- Wet Electrodes: Kindly wet the electrode area of the chest strap with a few drops of water for better conductivity.
- Pożizzjoni tal-ilbies: Adjust the sensor to the center of the heart with the Magene logo facing up. Ensure the electrode is close to the skin. The monitor should be worn under your chest and firmly against your skin.
- Qabbad mal-Apparat: Turn on your device (cycling computer, smartwatch, or app) and search for a connection to the sensor via ANT+ or Bluetooth.
3.2 Magene S3+ Speed/Cadence Sensor Setup
- Attivazzjoni tal-batterija: Open the battery compartment cover. Remove the insulating strip from the CR2032 battery. Reinstall the battery and compartment cover.
- Għażla tal-Modalità: Upon battery reinstallation, observe the LED light on the front of the unit:
- **Red LED:** Indicates Cadence mode.
- **Green LED:** Indicates Speed mode.
- Attach Rubber Pad: Select the appropriate rubber pad and install it on the back of the cadence sensor unit.
- Installation on Bicycle:
- Għal Kadenza: Attach the sensor to the crank arm using the provided rubber bands.
- Għall-Veloċità: Attach the sensor to the wheel hub using the provided rubber bands.
- Qabbad mal-Apparat: Spin the crankset (for cadence) or the wheel (for speed) to activate the sensor. Turn on your device (cycling computer, smartwatch, or app) and search for a connection to the sensor via ANT+ or Bluetooth.
4. Istruzzjonijiet Operattivi
4.1 Konnettività
Both the H003 Heart Rate Sensor and S3+ Speed/Cadence Sensor support dual-mode ANT+ and Bluetooth 4.0 protocols. This allows them to connect simultaneously to a wide range of devices and applications.
4.2 Compatible Devices & Apps
The sensors are compatible with various cycling computers, smartwatches, and fitness apps that support standard ANT+ or Bluetooth heart rate/speed/cadence protocols. Examples jinkludu:
- Apparati ANT+: Garmin, Bryton, iGPSPORT, Zwift, Onelap, Wahoo.
- Bluetooth Devices/Apps: XOSS, QICYCLE, Black Bird, Strava, Nike+, Wahoo Fitness.
5. Manutenzjoni
5.1 H003 Chest Strap Cleaning
After each use, rinse the chest strap under running water or with a mild lotion. Hang to dry. Do not machine wash or rub the strap vigorously, as this may damage the electrodes.
5.2 Sostituzzjoni tal-batterija
Both sensors use a CR2032 coin cell battery. To replace, open the battery compartment cover using a coin or a small tool. Remove the old battery and insert a new CR2032 battery with the positive (+) side facing up. Close the compartment cover securely.
5.3 Modalità Iffrankar tal-Enerġija
The H003 Heart Rate Sensor will enter sleep mode if no heart rate data is detected for 20 seconds. It will automatically wake up when data is detected again. The S3+ sensor also features an automatic sleep mode to conserve battery life when not in use.
6 Issolvi l-problemi
- No Data/Connection Issues:
- Ensure the battery is correctly installed and the insulating strip has been removed.
- For the H003 Heart Rate Sensor, ensure the electrodes on the chest strap are wet and making good contact with your skin.
- For the S3+ Speed/Cadence Sensor, ensure it is in the correct mode (red LED for cadence, green LED for speed) for your desired measurement. If not, remove and reinstall the battery to switch modes.
- Make sure your receiving device (cycling computer, phone app) has Bluetooth or ANT+ enabled and is actively searching for sensors. - Qari mhux eżatt:
- For heart rate, ensure the strap is snug and positioned correctly on your chest.
- For speed/cadence, ensure the sensor is securely mounted and not shifting during activity. - Sensor Stops Working:
- Replace the CR2032 battery. Battery life can vary based on usage and temperature.
7. Speċifikazzjonijiet
7.1 Magene H003 Heart Rate Sensor
| Karatteristika | Speċifikazzjoni |
|---|---|
| Daqs Ospitanti | 61.9 * 34.3 * 10mm |
| Chest Strap Size | 64-86cm (±2cm) |
| Heart Rate Unit | BPM |
| Eżattezza tar-Rata tal-Qalb | ± 1BPM |
| Ħajja tal-batterija | 1000 hours (affected by temperature and usage environment) |
| Interface bla wajers | Bluetooth 4.0, ANT+ |
| Mudell tal-batterija | CR2032 × 1 |
| Firxa tar-Rata tal-Qalb | 30-240BPM |
| Livell li ma jgħaddix ilma minnu | IP67 splash-proof (not for swimming) |
| Piż tas-Sensor | 13g |
7.2 Magene S3+ Speed/Cadence Sensor
| Karatteristika | Speċifikazzjoni |
|---|---|
| Konnessjoni bla fili | Bluetooth 4.0/ANT+ |
| Data Tracked | Cadence / Speed |
| Daqs | 85 * 29.8 * 38.3mm |
| Piż | 9g (inkluża l-batterija) |
| Waterproof | IP66 |
| Tip tas-Sensor | Senser ġeomanjetiku |
| Temperatura tax-Xogħol | -20-50℃ |
8. Għajnuniet għall-Utenti
- Iċċekkja tal-batterija: If you experience connection issues or the sensor stops working, first check and replace the CR2032 battery. Ensure the insulating strip is removed upon first use.
- Heart Rate Sensor Contact: Always wet the electrodes of the H003 chest strap before wearing to ensure optimal skin contact and accurate heart rate detection.
- S3+ Mode Verification: Double-check the LED indicator (red for cadence, green for speed) on your S3+ sensor to confirm it's in the desired mode for your activity.
- Kompatibilità: These sensors are widely compatible with many popular cycling computers and apps. If you have a specific device, verify its ANT+ or Bluetooth compatibility with heart rate/speed/cadence sensors.
9. Garanzija u Appoġġ
For warranty information and technical support, please refer to the official Magene website or contact your original point of purchase. Keep your proof of purchase for any warranty claims.
