HUTT S7 Window Cleaning Robot Instruction Manual

1. Introduzzjoni

The HUTT S7 Window Cleaning Robot is designed to provide efficient and thorough cleaning for various smooth glass surfaces. Featuring powerful suction, automatic water spray, and intelligent navigation, it simplifies window maintenance. This manual provides essential instructions for safe and optimal use of your device.

Image: HUTT S7 Window Cleaning Robot highlighting its main features.

2. Informazzjoni dwar is-Sigurtà

Please read all safety instructions carefully before operating the HUTT S7 Window Cleaning Robot. Failure to follow these instructions may result in injury or damage to the product.

2.1 Prekawzjonijiet Ġenerali

• Always ensure the safety rope is securely fastened to a solid, immovable object before operation.
• Do not use the robot on cracked or damaged glass surfaces.
• Ensure the window frame width is at least 6mm.
• The glass size must be larger than 30x30 cm.
• Avoid using the robot on irregularly shaped glass, curved glass, or surfaces with excessively large water droplets.
• Do not use on surfaces with decorations such as newspapers or stickers.
• Avoid use in environments with uneven, raised, leaking, or gaping glass glue.
• Do not place the machine on the ground after use if there are particles or other substances that could stick to the wiping cloth and scratch the glass.
• In case of remote control malfunction, pull the safety rope against the glass and slowly retrieve the machine.

Image: Safety features of the HUTT S7, including backup battery and safety rope.

3. Kontenut tal-Pakkett

Ivverifika li l-oġġetti kollha huma preżenti fil-pakkett:

• 1 x HUTT S7 Window Cleaning Robot
• 1 x Kaxxa tal-Ħażna
• 1 x Charger
• 5 x Żennuni
• 1 x Ħabel tas-Sigurtà
• 5 x Wiping Cloths
• 1 x Kontroll mill-bogħod
• 1 x Water Bottle (for filling)
• 1 x Manwal ta 'Istruzzjoni

Image: All-in-one storage box with included accessories.

4. Setup

4.1 Installing the Wiping Cloths

1. Stretch the bound edge of a wiping cloth and place it onto the turntable from the inside.
2. After half of the wiping cloth is on, gently press both sides with your hand and stretch to put on the remaining cloth.
3. Repeat for the other turntable. Ensure cloths are smooth and properly attached.

4.2 Mili tat-Tank tal-Ilma

1. Iftaħ il-għatu tat-tank tal-ilma.
2. Fill the tank with cleaning solution or clean water using the provided water bottle.
3. Plug the tank stopper tightly and check for any leakage.

4.3 Konnessjoni tal-Enerġija

1. Connect the power cord of the machine body to the adapter.
2. Qabbad il-korda tad-dawl tal-plagg mal-adapter.
3. Insert the power cord into a powered socket.

4.4 Fixing the Safety Rope

Hang the safety rope buckle on a solid, reliable, and immovable object. When fixing, it is advisable to wind it around the object one or two more times for added security.

Image: Visual guide for initial setup steps.

Video: Detailed instructions on how to use the HUTT S7, including cloth installation, water tank filling, power connection, and safety rope attachment.

5. Operazzjoni

5.1 Tibda tal-Magni

1. Press and hold the start button on the robot for 3 seconds to turn it on.
2. Place the machine on the glass surface, ensuring it is far from the window frame.
3. After confirming the machine is adsorbed on the glass, briefly press the circular start button for 1 second. The machine will begin working.

5.2 Automatic Route Planning

After starting, the machine will automatically move upward to the top vertex position. It will then move to the left, reaching the upper left corner of the window. From there, it will wipe the window from top to bottom in an S-shaped path. Depending on the shape of the glass, the machine will take either the lower left or lower right corner as the end point of wiping. Upon completing the work, the machine will return to its starting position.

5.3 L-użu tal-Kontroll mill-bogħod

The remote control allows for manual operation and mode selection:

• Sprej tal-Ilma: Press the water spray switch button to turn the water spray function on or off.
• Ċwievet tad-direzzjoni: Use the direction keys (up, down, left, right) to manually move the robot. Note that there is no water spray when moving in a single direction manually.
• X1 Key (Double Cleaning): Press the X1 key to initiate a second wiping cycle for deeper cleaning.
• Path Key (Fixed-Point Cleaning): Press the path key to make the machine wipe downward along a specific path from its current position.
• Circular Cleaning Key: Press this key to perform fixed-point cleaning.

Image: Remote control functions and intelligent path planning modes.

5.4 Removing the Machine

1. After the machine stops working, hold the machine firmly and press and hold the start button.
2. Once the machine operation sound becomes smaller, carefully remove the machine from the glass.
3. If the machine cannot be reached after the wiping work is completed, use the remote control to move it to a convenient position for manual retrieval, then remove it.

6. Manutenzjoni

6.1 Cleaning the Wiping Cloths

1. Remove the used wiping cloths from the turntables.
2. Soak the cloths in clean water at around 20°C for 2 minutes.
3. Clean them with a soft-bristled brush. Do not rub or wring them out forcefully.
4. Let them air dry naturally before using them again.

6.2 Chassis Cleaning

For the bottom suction port, wipe it clean with a dry cloth to avoid damage to the product's suction force.

6.3 Sostituzzjoni taż-Żennuna

If the machine cannot spray water in the wet wiping mode when turned on, it is considered that the nozzle is blocked and needs to be replaced.

1. L-ewwel, clamp the blue nozzle part with pliers and directly pull off the nozzle.
2. Find a new nozzle from the packaging accessories and press it directly into place for installation.

6.4 Storage After Use

1. After using the machine, please drain all the water from the water tank.
2. Replace the used wiping cloth with a clean and dry wiping cloth, or store it without a wiping cloth.
3. After the machine works in the wet wiping mode, it can be placed in a dry, ventilated, and cool place to disperse the moisture inside the machine for 1 to 2 days before storing it in its box.

7. Speċifikazzjonijiet

8. Garanzija u Appoġġ

Spare parts availability for this product is 2 years from the date of manufacture.

For technical support, troubleshooting, or warranty claims, please contact HUTT customer service through the retailer where you purchased the product or visit the official HUTT websit għal informazzjoni ta' kuntatt.