Fiamma Aluminium Wall Brackets for Awning Legs 98655-728

Introduzzjoni

This manual provides instructions for the proper installation, operation, and maintenance of your Fiamma Aluminium Wall Brackets for Awning Legs, model 98655-728. These brackets are designed to securely hold the support legs of your Fiamma awning against the wall of your recreational vehicle or camper, offering stability and convenience.

Informazzjoni dwar is-Sigurtà

• Aqra l-istruzzjonijiet kollha bir-reqqa qabel l-installazzjoni u l-użu.
• Kun żgur li l-wiċċ tal-immuntar ikun nadif, niexef, u strutturalment sod.
• Uża għodda xierqa u ilbes tagħmir tas-sigurtà waqt l-installazzjoni.
• Do not exceed the maximum weight recommendation of 138 grams per bracket.
• Regularly inspect the brackets for signs of wear or damage. Replace immediately if any damage is found.

Kontenut tal-Pakkett

Iċċekkja li l-komponenti kollha huma preżenti qabel tibda l-installazzjoni.

Image: Components of the Fiamma Aluminium Wall Brackets kit, including two aluminum brackets, two black plastic base plates, two black plastic leg holders, four screws, and two metal shims.

• 2x Aluminium Wall Brackets
• 2x Black Plastic Base Plates
• 2x Black Plastic Leg Holders
• 4x Viti tal-Immuntar
• 2x Metal Shims (if included in your specific kit)

Setup u Installazzjoni

These brackets are designed for wall-mount installation on metal surfaces.

1. Agħżel Post: Select a suitable, flat, and structurally sound area on your RV or camper wall where the awning legs will rest when retracted. Ensure the location allows for proper support and does not interfere with other components.
2. Wiċċ Nadif: Thoroughly clean the mounting surface to remove any dirt, grease, or debris. A clean surface is essential for secure attachment.
3. Position Base Plate: Place one black plastic base plate against the cleaned wall at the desired mounting point. Mark the screw holes.
4. Drill Pilota Toqob: Carefully drill pilot holes at the marked locations. Ensure the drill bit size is appropriate for the provided screws to prevent stripping or cracking the mounting surface.
5. Waħħal il-Pjanċa tal-Bażi: Secure the black plastic base plate to the wall using two mounting screws. It is recommended to apply a suitable sealant (e.g., silicone) around the screw holes and under the base plate to prevent water ingress.
6. Install Aluminium Bracket: Slide the aluminium wall bracket onto the attached black plastic base plate. Ensure it clicks securely into place.
7. Repeat for Second Bracket: Follow steps 3-6 to install the second bracket at the appropriate distance for your awning leg.
8. Stabbiltà tat-Test: Once both brackets are installed, gently test their stability. Ensure they are firmly attached to the wall.

Immaġni: Close-up view of the Fiamma Aluminium Wall Brackets and associated hardware, showing the individual pieces before assembly.

Istruzzjonijiet Operattivi

To use the Fiamma Aluminium Wall Brackets with your awning legs:

1. Extend Awning Legs: Extend your awning legs as per your awning's instructions.
2. Position Legs: Guide the bottom end of each awning leg into the corresponding aluminium wall bracket.
3. Saqajn Sikuri: Ensure the awning legs are fully seated and secured within the brackets. The design of the bracket is intended to hold the leg firmly.
4. Retract Awning: When retracting your awning, carefully remove the legs from the wall brackets before fully stowing the awning.

Manutenzjoni

• Tindif: Clean the brackets periodically with mild soap and water. Avoid abrasive cleaners that could damage the aluminum finish.
• Spezzjoni: Regularly inspect the brackets and mounting screws for any signs of loosening, corrosion, or damage. Tighten screws if necessary.
• Kontroll tas-Siġillant: Periodically check the sealant around the mounting points for cracks or deterioration. Reapply sealant as needed to maintain a watertight seal.

Issolvi l-problemi

Bracket Not Sticking/Loosening

If a bracket does not adhere properly or loosens over time:

• Re-clean Surface: Ensure the mounting surface was thoroughly cleaned and free of contaminants before installation.
• Iċċekkja Viti: Verify that the mounting screws are tightened securely. Do not overtighten.
• Applika mill-ġdid is-siġillant: If the issue is related to the seal, remove the bracket, clean the area, and reapply a fresh, high-quality sealant before re-mounting.
• Spezzjona għal Ħsara: Check the bracket and the wall for any damage that might prevent a secure fit.

Speċifikazzjonijiet

• Mudell: 98655-728
• Materjal: Aluminju
• Tip ta 'Finish: Silber (Silver)
• Tip ta 'Immuntar: Mount Wall
• Piż tal-oġġett: Madwar 0.18 Kilogrammi (6.3 uqija)
• Dimensjonijiet tal-Prodott (L x W x H): 3.82 x 4.37 x 1.42 pulzieri
• Rakkomandazzjoni tal-Piż Massimu: 138 Grams (per bracket)
• Rakkomandazzjoni tal-wiċċ: Metall
• Number of Hooks: 2 (referring to the set of two brackets)

Garanzija u Appoġġ

For warranty information or technical support, please refer to the official Fiamma website or contact your authorized Fiamma dealer. Keep your purchase receipt as proof of purchase.