1. Introduzzjoni
The UMLIFE STC-1000 is a versatile digital temperature controller designed for precise temperature management in various applications. This device features a clear LED display, NTC 10K thermistor sensor, and dual relay outputs for both heating and cooling control. This manual provides detailed instructions for installation, operation, and maintenance to ensure optimal performance and longevity of your temperature controller.
2. Prodott Aktarview
2.1 Karatteristiċi ewlenin
- Digital LED display for clear temperature readings.
- Wide temperature measurement and control range: -50°C to 99°C.
- High control accuracy of 0.1°C.
- Dual relay output for simultaneous heating and cooling control.
- Waterproof NTC 10K thermistor sensor for reliable measurements in various environments.
- Funzjoni ta 'kalibrazzjoni tat-temperatura.
- Delay start protection for cooling control.
- ABS flame-retardant shell for enhanced safety.
2.2 Komponenti u Wiri
Familiarize yourself with the main components and display interface of the STC-1000 controller.
Figura 1: Front panel of the STC-1000 controller showing the digital display, power switch, UP button, Setting button, and DOWN button.
- Digital Display Window: Shows current temperature and parameter settings.
- Swiċċ tal-Enerġija: Ixgħel jew jitfi l-apparat.
- Buttuna 'l fuq (▲): Iżid il-valuri jew jinnaviga l-menus.
- Buttuna 'L ISFEL (▼): Inaqqas il-valuri jew jinnaviga l-menus.
- Setting Button (S): Jidħol fil-modalità tal-issettjar tal-parametri.
- Cool Indicator: Illuminates when cooling relay is active.
- Indikatur tas-Sħana: Illuminates when heating relay is active.
Figura 2: Physical dimensions of the STC-1000 controller and the included 1-meter NTC 10K waterproof sensor probe.
3. Speċifikazzjonijiet
| Parametru | Valur |
|---|---|
| Mudell | STC-1000 |
| Firxa tal-Kejl tat-Temperatura | -50°C sa 99°C |
| Firxa ta 'Kontroll tat-Temperatura | -50°C sa 110°C |
| Preċiżjoni tal-Kejl | ±0.2°C |
| Riżoluzzjoni | 0.1°C |
| Kontroll Preċiżjoni | ±0.1°C |
| Sensor | NTC 10K L=1M waterproof probe |
| Provvista tal-Enerġija | DC 12V |
| Konsum tal-Enerġija | <3W |
| Kapaċità ta 'Kuntatt tar-Relay | Cool (10A/220VAC), Heat (10A/220VAC) |
| Temperatura Ambjentali | 0°C sa 60°C |
| Temperatura tal-Ħażna | -30°C sa 75°C |
| Umdità Relattiva | 20-84% |
| Daqs tal-Immuntar | 71mm x 29mm |
| Dimensjonijiet tal-Prodott | 75mm x 34.5mm x 85mm |
| Piż tal-oġġett | 7 uqija (madwar 198g) |
| Materjal | Acrylonitrile Butadiene Styrene (ABS) |
4. Setup u Installazzjoni
Avviż Importanti dwar is-Sigurtà: Installation should be performed by qualified personnel. Ensure power is disconnected before wiring to prevent electric shock. Strictly distinguish between power supply, sensor, and relay interfaces. Maintain proper distance between sensor down-lead and power wires to avoid interference.
4.1 Dijagramma tal-Wiring
Refer to the following diagram for correct wiring connections. This model operates on DC 12V power supply.
Figura 3: Wiring diagram for the STC-1000 12V temperature controller. Connections are for power supply, NTC sensor, heating relay, and cooling relay.
- Terminali 1 u 2: Power Supply (DC 12V).
- Terminali 3 u 4: NTC Sensor connection.
- Terminali 5 u 6: Heating Relay Output (Connect to heating device).
- Terminali 7 u 8: Cooling Relay Output (Connect to cooling device).
Ensure all connections are secure and insulated. Verify the power supply voltage matches the controller's requirement (DC 12V for this model).
4.2 Immuntar
The STC-1000 is designed for panel mounting. Cut an opening of 71mm x 29mm in your panel. Insert the controller and secure it using the provided clips or mounting brackets.
5. Istruzzjonijiet Operattivi
The STC-1000 operates in Celsius only. It cannot be switched to Fahrenheit.
5.1 Power On/Off
- Agħfas il- Swiċċ tal-Qawwa button (marked with ⏻) to turn the controller on or off.
5.2 Setting Temperature Parameters
The controller has two main temperature settings: the Set Temperature (ST) u l- Difference Temperature (DT), also known as hysteresis.
- Biex view the Set Temperature (ST): Agħfas fil-qosor il- Setting (S) button. The display will show the current set temperature.
- To modify the Set Temperature (ST):
- Agħfas u żomm il- Setting (S) button for approximately 3 seconds until the display flashes.
- Uża l- LUP (▲) or NIŻEL (▼) buttuni biex taġġusta t-temperatura ssettjata mixtieqa.
- Agħfas il- Swiċċ tal-Qawwa button to save the setting and exit, or wait for 10 seconds for it to save automatically.
5.3 Advanced Parameter Settings (F1-F4)
To access and modify advanced parameters:
- Agħfas u żomm il- Setting (S) button for approximately 3 seconds until the display flashes.
- Waqt li d-displej ikun qed jteptep, agħfas il-buttuna Setting (S) button again (do not hold) to cycle through parameters F1, F2, F3, F4.
- Uża l- LUP (▲) or NIŻEL (▼) buttons to adjust the value of the selected parameter.
- Agħfas il- Swiċċ tal-Qawwa button to save the setting and exit, or wait for 10 seconds for it to save automatically.
| Parametru | Deskrizzjoni | Firxa | Default |
|---|---|---|---|
| F1 | Difference Temperature (Hysteresis): The difference between the set temperature and the temperature at which the relay switches off. | 0.3°C sa 10°C | 2.0°C |
| F2 | Highest Set Point Limit: Limits the maximum adjustable set temperature. | Set Temp to 110°C | 110°C |
| F3 | Lowest Set Point Limit: Limits the minimum adjustable set temperature. | -50°C to Set Temp | -50°C |
| F4 | Kalibrazzjoni tat-Temperatura: Adjusts the temperature reading to match a known accurate thermometer. | -10°C sa 10°C | 0.0°C |
5.4 Modi ta' Tisħin u Tkessiħ
The STC-1000 automatically switches between heating and cooling based on the set temperature (ST) and difference temperature (DT).
- Modalità tat-tkessiħ: If the current temperature is higher than (ST + DT), the cooling relay activates. It deactivates when the temperature drops to ST.
- Modalità tat-Tisħin: If the current temperature is lower than (ST - DT), the heating relay activates. It deactivates when the temperature rises to ST.
6. Manutenzjoni
- Tindif: Imsaħ il-wiċċ tal-kontrollur b'ċarruta ratba u niexfa. Tużax prodotti tat-tindif jew solventi li joborxu.
- Kura tas-Sensor: Ensure the NTC sensor probe is clean and free from debris. While waterproof, avoid unnecessary physical damage to the probe or cable.
- Konnessjonijiet: Periodically check wiring connections for tightness and signs of corrosion.
- Ambjent: Operate the controller within the specified ambient temperature and humidity ranges to ensure optimal performance and lifespan.
7 Issolvi l-problemi
| Problema | Kawża Possibbli | Soluzzjoni |
|---|---|---|
| Display shows "EE" | Sensor error or open circuit. | Check sensor connection. Replace sensor if damaged. |
| Display shows "HHH" | Temperature exceeds upper limit of measurement range. | Ensure the environment temperature is within the sensor's range (-50°C to 99°C). |
| Display shows "LLL" | Temperature falls below lower limit of measurement range. | Ensure the environment temperature is within the sensor's range (-50°C to 99°C). |
| Kontrollur mhux mixgħul | L-ebda provvista tal-enerġija jew volum mhux korretttage. | Check power connections and ensure DC 12V is supplied. |
| It-tisħin/tkessiħ mhux qed jattiva | Incorrect temperature settings (ST, DT), wiring error, or device malfunction. | Verify ST and DT settings. Check heating/cooling device wiring. Ensure the device is within operating parameters. |
8. Garanzija u Appoġġ
UMLIFE products are manufactured to high-quality standards. For warranty information or technical support, please contact UMLIFE customer service through your purchase platform or visit the official UMLIFE website. Please have your product model (STC-1000 12V) and purchase details ready when contacting support.
Għal aktar għajnuna, tista' tirreferi wkoll għall- UMLIFE Store on Amazon.