Flysky FS-i6X 10CH 2.4GHz AFHDS 2A RC Transmitter User Manual

1. Introduzzjoni

This manual provides detailed instructions for the operation, setup, and maintenance of your Flysky FS-i6X 10-channel 2.4GHz AFHDS 2A RC Transmitter and FS-iA10B Receiver. This system is designed for use with fixed-wing aircraft, gliders, and helicopters, offering reliable and precise control.

The FS-i6X transmitter and FS-iA10B receiver are pre-bound at the factory. Therefore, re-binding is generally not required upon initial receipt. Please read this manual thoroughly before operating the device to ensure safe and correct usage.

2. Kontenut tal-Pakkett

Iċċekkja li l-oġġetti kollha elenkati hawn taħt huma inklużi fil-pakkett tiegħek:

• 1x Flysky FS-i6X Transmitter
• 1x FS-iA10B Receiver
• 1x Bind Plug
• 1x Upgrade Cable

Nota: Il-batteriji mhumiex inklużi u jridu jinxtraw separatament.

3. Prodott Aktarview

Figure 3.1: Flysky FS-i6X Transmitter and FS-iA10B Receiver included in the package.

3.1 FS-i6X Transmitter Components

Figura 3.2: Quddiem view of the FS-i6X Transmitter with key components labeled.

• Antenna: Transmits the radio signal to the receiver.
• Hand Lever: For carrying the transmitter.
• VrA, VrB: Rotary potentiometers for auxiliary channel control.
• SwA, SwB, SwC, SwD: Two-position switches for auxiliary channel control.
• Strap Ring: Attachment point for a neck strap.
• Joystick tax-Xellug: Controls elevator and rudder (Mode 2 default).
• Joystick tal-lemin: Controls aileron and throttle (Mode 2 default).
• Fine-tuning bars (1-4): Used for precise adjustment of joystick center points.
• Buttuni UP/DOWN: Innaviga l-għażliet tal-menu.
• Buttuna OK: Jikkonferma l-għażliet fil-menù.
• Ikkanċella Buttuna: Exits menu or cancels current operation.
• BIND KEY: Initiates the binding process.
• Buttuna POWER: Ixgħel/itfi t-trasmettitur.
• Wiri: LCD screen showing system information and menu.

3.2 FS-iA10B Receiver Components

Figura 3.3: Close-up view of the FS-iA10B Receiver showing servo ports and antenna.

• Channels 1-10 (CH1-CH10): Ports for connecting servos and other control devices.
• i-BUS Port: For digital serial data output.
• Data Acquisition Port: For connecting sensors and telemetry modules.
• Antenna (Dual): Receives radio signals from the transmitter.
• Power Input (VCC): Connects to the power source (4.0-6.5V DC).

4. Setup

4.1 Installazzjoni tal-Batterija (Trasmettitur)

The FS-i6X Transmitter requires four (4) AA batteries (1.5V each) for a total of 6V DC power. Ensure correct polarity when inserting batteries.

1. Iftaħ l-għatu tal-kompartiment tal-batterija fuq wara tat-trasmettitur.
2. Insert four AA batteries according to the polarity markings (+/-) inside the compartment.
3. Agħlaq l-għatu tal-kompartiment tal-batterija sew.

Figura 4.1: Wara view of the FS-i6X Transmitter showing the battery compartment.

4.2 Konnessjoni tar-riċevitur

Connect your servos and other control devices to the appropriate channels on the FS-iA10B receiver. Ensure that the power supply for the receiver is within the specified range of 4.0-6.5V DC.

4.3 Proċedura vinkolanti

The FS-i6X transmitter and FS-iA10B receiver are pre-bound from the factory. You do not need to bind them again upon receipt. However, if you need to re-bind or bind to a new receiver, follow these steps:

1. Kun żgur li t-trasmettitur ikun mitfi.
2. Insert the bind plug into the B/VCC port on the FS-iA10B receiver.
3. Connect power to the receiver. The receiver's LED should flash rapidly, indicating it is in binding mode.
4. While holding down the BIND KEY on the transmitter, turn on the transmitter.
5. Release the BIND KEY once the transmitter display shows "RX Binding" or similar.
6. The receiver's LED should turn solid, indicating successful binding.
7. Itfi kemm it-trasmettitur kif ukoll ir-riċevitur.
8. Neħħi t-tapp tal-irbit mir-riċevitur.
9. Turn on the transmitter first, then the receiver. The system should now be bound and operational.

5. Istruzzjonijiet Operattivi

5.1 Tixgħel/Jitfi

• Biex Tixgħel: Press and hold the POWER button on the transmitter until the display illuminates.
• Biex Tifi: Press and hold the POWER button until the display turns off.

5.2 Channel Setup (Enabling 10 Channels)

The FS-i6X transmitter defaults to 6 channels. To enable all 10 channels, follow these steps:

1. Agħfas fit-tul il- OK button for 2 seconds to enter the main menu setting.
2. Innaviga lejn u agħżel Setup tas-sistema.
3. Scroll down to the last item, Aux SWitches (auxiliary switch setting), and select it to enter.
4. For switches SwA, SwB, SwC, SwD, set their selection to On biex jattivahom.
5. Change the channel assignment from Ch6 biex Ch10.
6. Agħfas fit-tul il- IKANNELLA button to automatically save the settings and exit the menu.

5.3 Vol baxxtage Twissija

The transmitter features a low voltage warning system. If the battery voltage drops below 4.2V, an alert will be displayed on the LCD screen, indicating that the batteries need to be replaced or recharged (if using rechargeable batteries).

6. Speċifikazzjonijiet

6.1 FS-i6X RC Transmitter Specifications

6.2 FS-iA10B Receiver Specifications

7. Manutenzjoni

• Keep the transmitter and receiver clean and free from dust and moisture. Use a soft, dry cloth for cleaning.
• Avoid exposing the devices to extreme temperatures, direct sunlight, or corrosive materials.
• Neħħi l-batteriji mit-trasmettitur jekk ma jkunx se jintuża għal perjodu estiż biex tevita t-tnixxija.
• Regularly check all connections for secure fit.

8 Issolvi l-problemi

9. Support and Online Resources

For further assistance, firmware updates, or additional product information, please visit the official Flysky website. Online communities and forums dedicated to RC hobbies can also provide valuable support and tips.

The FS-i6X supports online updates. Refer to the official Flysky website for instructions on how to perform firmware updates using the provided upgrade cable.