Manwal tal-Istruzzjonijiet tal-Attwatur Universali Wireless Eltako FUA12-230V

1. Introduzzjoni

This manual provides comprehensive instructions for the installation, operation, and maintenance of the Eltako FUA12-230V Wireless Universal Actuator. Please read this manual thoroughly before using the device to ensure safe and efficient operation.

2. Informazzjoni dwar is-Sigurtà

TWISSIJA: Riskju ta' xokk elettriku!

• L-installazzjoni u l-manutenzjoni għandhom isiru biss minn elettriċista kwalifikat.
• Disconnect power before performing any work on the device.
• Kun żgur li l-wajers kollha jikkonformaw mal-kodiċijiet elettriċi lokali u nazzjonali.
• Do not operate the device if it is damaged or has been exposed to moisture.
• Dan l-apparat huwa ddisinjat għall-użu fuq ġewwa biss.

3. Prodott Aktarview

The Eltako FUA12-230V is a wireless universal actuator featuring a replaceable antenna and a surge switch relay. It provides a potential-free contact with a rating of 10A/250V AC, suitable for various control applications, including roller shutters and general impulse relay functions.

Figura 1: Eltako FUA12-230V Wireless Universal Actuator. The image displays the blue-colored actuator with its replaceable antenna connected via a coaxial cable. The front panel shows the Eltako brand logo, model number FUA12-230V, and CE marking. Below this are three rotary dials for settings: one for ESV t(min) and ER t(s) timing (0-120 seconds/minutes), one for AUTO, CLR, LRV, LRN functions, and a third for ESV/ER mode selection and output configuration (10A/250V~). The bottom section reveals screw terminals labeled N, L, 15(L), and 18 for electrical connections.

Karatteristiċi ewlenin:

• Wireless universal actuator with replaceable antenna.
• Surge switch relay with 1 potential-free changer contact (10A/250V AC).
• Radio receiver functionality.
• Suitable for roller shutter switches.
• Push button operation.
• Wireless impulse relay.

4. Setup u Installazzjoni

Qabel ma tipproċedi bl-installazzjoni, kun żgur li l-provvista ewlenija tal-enerġija hija skonnettjata.

4.1 Konnessjonijiet tal-Wiring

Refer to the terminal markings on the device (N, L, 15(L), 18) for correct electrical connections. The device operates on 230V~.

• N: Konduttur newtrali.
• L: Live conductor (230V~).
• 15(L): Common contact for the potential-free relay. Connect the load's live wire here.
• 18: Normally Open (NO) contact of the potential-free relay. Connect the other side of the load here.
• Ensure secure connections for all wires.

4.2 Installazzjoni tal-antenna

The device comes with a replaceable antenna. Connect the antenna securely to the designated connector on the actuator. Position the antenna for optimal signal reception, avoiding metallic obstructions.

4.3 Learning-in Process (Pairing)

To pair the actuator with a wireless transmitter (e.g., a wireless push button), follow these steps:

1. Restore power to the actuator.
2. Set the middle rotary dial to the "LRN" position. The device will enter learning mode.
3. Activate the desired function on your wireless transmitter (e.g., press the push button).
4. The actuator will confirm successful pairing, typically by a relay click or LED indication (refer to specific transmitter manual for confirmation).
5. Return the middle rotary dial to "AUTO" or the desired operating mode.

To clear learned transmitters, set the middle rotary dial to "CLR" and follow the device-specific instructions for clearing memory.

5. Istruzzjonijiet Operattivi

The Eltako FUA12-230V offers various operating modes and timing functions controlled by the front panel dials.

5.1 Għażla tal-Modalità

• AUTO: Standard operating mode where the actuator responds to learned wireless commands.
• LRV: (Likely) Local Reset Value or similar function, consult full Eltako documentation for precise meaning.
• LRN: Learning mode for pairing transmitters (as described in Section 4.3).
• CLR: Clear mode for deleting learned transmitters.

5.2 Timing Functions (ESV t(min) / ER t(s))

The top dial controls timing parameters for ESV (Electronic Surge Switch) and ER (Electronic Relay) functions. The settings range from 0 to 120, representing either minutes (t(min)) or seconds (t(s)) depending on the selected mode.

• Adjust the dial to set the desired delay or pulse duration for the relay output.
• The specific behavior (e.g., on-delay, off-delay, pulse) depends on the ESV/ER mode selected via the bottom dial.

5.3 ESV / ER Mode Selection

The bottom dial allows selection between ESV and ER modes, and potentially other configurations related to the relay's behavior. The output contact rating is 10A/250V~.

• Consult the detailed Eltako product documentation for a complete explanation of each ESV and ER mode and their corresponding functionalities.

6. Manutenzjoni

The Eltako FUA12-230V is designed for long-term, maintenance-free operation. However, periodic checks can ensure optimal performance.

• Tindif: Gently wipe the exterior of the device with a dry, soft cloth. Do not use liquid cleaners or solvents.
• Konnessjonijiet: Periodically check electrical connections for tightness, especially after initial installation. Ensure no wires are loose.
• Antenna: Kun żgur li l-antenna hija konnessa sew u bla ħsara.

No user-serviceable parts are inside the enclosure. Do not attempt to open or repair the device yourself.

7 Issolvi l-problemi

If the actuator is not functioning as expected, consider the following:

• Ebda Tweġiba:
  • Check if the power supply to the actuator is active.
  • Verify that the wireless transmitter is functioning and has sufficient battery power (if applicable).
  • Ensure the actuator is correctly paired with the transmitter (refer to Section 4.3).
  • Check the antenna connection and position.
• Operazzjoni Mhux Korretta:
  • Review the operating mode and timing settings on the front panel dials (Section 5).
  • Ensure the wiring connections are correct according to Section 4.1.
• Operazzjoni intermittenti:
  • Check for sources of radio interference near the actuator or transmitter.
  • Ensure the antenna is not obstructed by metallic objects.

If problems persist, contact Eltako customer support or a qualified electrician.

8. Speċifikazzjonijiet

9. Garanzija u Appoġġ

For warranty information and technical support, please refer to the official Eltako website or contact your local Eltako distributor. Keep your purchase receipt as proof of purchase.

Eltako Official Websit: www.eltako.com