M-Wave MWAVE CVC1012 Computer 14 F M14W

1. Introduzzjoni

The M-Wave M14W is a wired bicycle computer designed to provide essential cycling data. It features 14 functions to help you track your rides effectively. Please read this manual carefully before installation and use to ensure proper function and longevity of your device.

Figura 1: Quddiem view of the M-Wave M14W bicycle computer, showing the display with current speed (37.0 KM/hr) and distance (2.625).

2. Kontenut tal-Pakkett

Before proceeding with installation, verify that all components are present in the package:

• M-Wave M14W Bicycle Computer Unit
• Wired Sensor and Cable
• Bracket tal-Immuntar
• Kalamita tar-rota
• Cable Ties for securing
• Batterija CR2 (installata minn qabel jew inkluża separatament)
• Manwal ta 'Istruzzjoni (dan id-dokument)

Figure 2: The M-Wave M14W bicycle computer shown in its retail packaging, indicating wireless functionality and 14 functions.

3. Setup u Installazzjoni

3.1 Installazzjoni tal-batterija

The M-Wave M14W uses a CR2 battery. The battery may be pre-installed. If not, or if you need to replace it:

1. Locate the battery compartment on the back of the computer unit.
2. Use a small coin or screwdriver to open the battery cover by twisting it counter-clockwise.
3. Daħħal il-batterija CR2 bin-naħa pożittiva (+) tħares 'il fuq.
4. Erġa’ poġġi l-għatu tal-batterija u dawwar lejn l-arloġġ biex twaħħalha.

Figura 3: Wara view of the M-Wave M14W unit, showing the battery compartment and reset button.

3.2 Mounting the Computer and Sensor

Follow these steps to securely mount the computer and its wired sensor:

1. Bracket tal-immuntar: Attach the mounting bracket to your handlebar or stem using the provided straps or cable ties. Ensure it is firmly secured and positioned for easy viewing.
2. Tqegħid tas-Sensor: Mount the wired sensor to the front fork of your bicycle, ensuring it is aligned with the wheel magnet. The sensor should be positioned so that the magnet passes within 5mm of the sensor as the wheel rotates.
3. Installazzjoni tal-Kalamita: Attach the magnet to a spoke on your front wheel. Adjust its position so it aligns with the sensor.
4. Rotot tal-kejbil: Route the sensor cable along the fork and frame, securing it with cable ties to prevent it from interfering with moving parts or getting snagged. Plug the cable into the computer unit's port.
5. Computer Attachment: Slide the M14W computer unit onto the mounting bracket until it clicks into place.

3.3 Settings Inizjali

After installation, you will need to configure the basic settings:

1. Għażla tal-Unità: Agħfas il- MODALITÀ button to cycle through settings. When prompted, select your preferred unit of speed (KM/hr or MPH) using the SET button. Confirm with MODALITÀ.
2. Ċirkonferenza tar-Rota: This is crucial for accurate speed and distance readings.
   • Refer to your bicycle tire's sidewall for its size (e.g., 700x23C, 26x1.95).
   • Consult a wheel circumference chart (available online or in bicycle shops) to find the corresponding value in millimeters (mm).
   • Enter this value into the computer using the SET button to adjust digits and MODALITÀ biex timxi għaċ-ċifra li jmiss.
3. Initial Odometer Setting (Optional): Some models allow setting an initial odometer value. Follow on-screen prompts if this option appears.

4. Istruzzjonijiet Operattivi

The M14W features two primary buttons: SET u MODALITÀ.

• Buttuna MODE: Used to cycle through different display functions (e.g., Speed, Distance, Ride Time, Odometer). In setting mode, it confirms selections or moves to the next setting.
• Buttuna SET: Used to adjust values during setup (e.g., wheel circumference, time). In some modes, it may reset specific trip data.

4.1 Display Functions (14 Functions)

Agħfas il- MODALITÀ buttuna biex view il-funzjonijiet li ġejjin:

4.2 Resetting Trip Data

To reset trip-specific data (Trip Distance, Average Speed, Maximum Speed, Ride Time), typically you will press and hold the SET button for a few seconds while in the relevant display mode. Refer to the on-screen prompts for confirmation.

5. Manutenzjoni

5.1 Tindif

Clean the computer unit and sensor regularly with a soft, damp drapp. Tużax prodotti tat-tindif jew solventi li joborxu, għax dawn jistgħu jagħmlu ħsara lid-displej jew liċ-ċasing. The unit has an IP44 rating, meaning it is protected against solid objects larger than 1mm and splashing water from any direction. Avoid submerging the unit in water.

5.2 Sostituzzjoni tal-batterija

When the display becomes dim or erratic, it's time to replace the CR2 battery. Follow the steps outlined in Section 3.1. Dispose of old batteries responsibly according to local regulations.

5.3 Ħażna

If storing the bicycle computer for an extended period, it is recommended to remove the battery to prevent leakage and potential damage to the unit.

6 Issolvi l-problemi

If you encounter issues with your M-Wave M14W computer, try the following solutions:

7. Speċifikazzjonijiet

8. Garanzija u Appoġġ

M-Wave products are manufactured to high quality standards. For specific warranty information, please refer to the warranty card included with your product or visit the official M-Wave website. In case of technical issues or questions not covered in this manual, please contact M-Wave customer support through their official channels.

Figure 4: M-Wave brand logo, "Your World of Cycling".

For more information and product updates, you may visit the official M-Wave websit: www.m-wave-bike.com