RAB Lighting GT500 Motion Sensor Light Outdoor Instruction Manual

1. Informazzjoni Importanti dwar is-Sigurtà

Please read these instructions carefully before installation and operation. Failure to follow these instructions may result in electric shock, fire, or other hazards, which could cause property damage, serious injury, or death.

• TWISSIJA: Riskju ta' Xokk Elettriku. Skonnettja l-enerġija fil-fjus jew circuit breaker qabel l-installazzjoni jew is-servizz.
• L-installazzjoni għandha titwettaq minn elettriċista kwalifikat skont il-kodiċijiet elettriċi nazzjonali u lokali kollha.
• Tiżgura l-provvista voltage is correct for the fixture (120V or 277V).
• Tinstallax ħdejn materjali kombustibbli.
• This device is designed for outdoor, wet-rated locations.
• Use only with PAR38 flood lamps up to 150W max.

2. Prodott Aktarview

The RAB Lighting GT500W is a hardwired outdoor motion sensor designed to provide reliable security lighting. It features a 110-degree detection range and is compatible with 120V and 277V systems, supporting up to 600W at 120V and 1350W at 277V. Its durable polycarbonate housing and 6000V surge protection ensure long-term performance in various weather conditions.

Figura 2.1: Quddiem view of the RAB Lighting GT500 Motion Sensor Light.

Karatteristiċi ewlenin:

• Sejbien ta' Moviment Affidabbli: 110° coverage for dependable security.
• Doppju Voltage Kapaċità: Supports 120V and 277V installations.
• Heavy-Duty Surge Protection: Built with 6000V surge protection.
• Kostruzzjoni Durabbli: Polycarbonate housing for wet-rated outdoor performance.
• Adjustable Timing: Run time from 10 seconds to 15 minutes.
• Override manwali: 6-hour protected manual override for continuous light.
• Lamp Kompatibilità: Designed for PAR38 flood lamps up to 150W max.

3. Installazzjoni (Setup)

Before beginning installation, ensure all power is disconnected at the circuit breaker or fuse box. This device is designed for wall mount installation.

3.1 Immuntar

1. Select a suitable mounting location, typically 8-15 feet above the ground, ensuring the sensor has an unobstructed view of the desired detection area.
2. Securely attach the sensor to a junction box using appropriate hardware (not included). Ensure a watertight seal for outdoor applications.

3.2 Wajers

The GT500W sensor is hardwired and supports both 120V and 277V electrical systems. Refer to the wiring diagram below and consult a qualified electrician if unsure.

Figure 3.1: Wiring connections for the GT500W sensor. Black wire for Line, White for Neutral, Red for Load.

• Qabbad il- ISWED wire from the sensor to the LINJA (HOT) wire from the power supply.
• Qabbad il- ABJAD wire from the sensor to the NEWTRALI wire from the power supply.
• Qabbad il- AĦMAR wire from the sensor to the LOAD (fixture) wajer.
• Ensure all connections are secure and insulated with approved wire connectors.
• Irrestawra l-enerġija fis-circuit breaker.

4. Operazzjoni

The GT500W sensor automatically detects motion and activates connected lighting. It features adjustable settings for optimal performance.

4.1 Medda ta 'Sejbien

The sensor provides a 110-degree field of view, detecting motion up to 70 feet away. The coverage area can be influenced by mounting height and environmental factors.

Figure 4.1: The 110-degree detection range of the GT500 sensor.

4.2 Aġġustament tas-Settings

The sensor includes controls for adjusting the run time and sensitivity. These controls are typically located on the underside or side of the sensor unit.

Figura 4.2: Eżample of adjustable sensitivity control.

• Aġġustament tal-ĦIN: This dial controls how long the light remains on after motion is detected. Settings typically range from 10 seconds to 15 minutes. Turn the dial clockwise to increase the duration, counter-clockwise to decrease.
• SENSITIVITY Adjustment: This dial controls the sensor's responsiveness to motion. Turn the dial clockwise for higher sensitivity (detects smaller movements or at greater distances), and counter-clockwise for lower sensitivity (reduces false triggers).

4.3 Manwal Override

The GT500W features a 6-hour protected manual override function, allowing the light to stay on continuously regardless of motion detection.

• To activate manual override, quickly turn the light switch OFF and then ON within 2 seconds. The light will remain ON for approximately 6 hours.
• To deactivate manual override and return to motion-sensing mode, quickly turn the light switch OFF and then ON again. The light will then operate based on motion detection and set time.

5. Manutenzjoni

The RAB Lighting GT500W motion sensor is designed for minimal maintenance.

• Tindif: Naddaf il-lenti tas-sensorju perjodikament b'ċarruta ratba u damp cloth to remove dirt, dust, or debris that may obstruct detection. Do not use abrasive cleaners or solvents.
• Lamp Sostituzzjoni: If the connected PAR38 flood lamps fail, ensure power is disconnected before replacing them. Follow the lamp manufacturer's instructions for replacement.

6 Issolvi l-problemi

If the motion sensor light is not functioning as expected, refer to the following common issues and solutions:

7. Speċifikazzjonijiet

8. Garanzija u Appoġġ

8.1 Garanzija tal-Manifattur

The RAB Lighting GT500W Motion Sensor Light is covered by a Garanzija ta' 1 snin mill-manifattur from the date of purchase. This warranty covers defects in materials and workmanship under normal use. It does not cover damage resulting from improper installation, accident, abuse, misuse, or unauthorized modification.

8.2 Appoġġ għall-Klijent

For technical assistance, warranty claims, or further information, please contact RAB Lighting customer support:

• Websit: www.rablighting.com
• Telefon: Irreferi għar-RAB Lighting websit għal numri ta' kuntatt attwali.
• Email: Irreferi għar-RAB Lighting websit għall-email tal-kuntatt attwali.

Please have your model number (GT500W) and proof of purchase available when contacting support.